Fast drying minwax polyurethane

Fast drying minwax polyurethane DEFAULT

Directions

Instrucciones en Español
Instructions for using Minwax® Fast-Drying Polyurethane.

For aerosol directions, click here

Interior Use Only

WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.

Directions:

  1. Surface must be dry and free of old finishes in poor condition, paint, wax, grease, polish, dirt or other foreign matter.
  2. Sand to obtain a smooth uniform surface. Remove all dust with a cloth dampened with mineral spirits.
  3. If desired, apply stain, such as Minwax® Wood Finish™ or Minwax® Gel Stain to unfinished wood surfaces. Follow directions for application and dry times.
  4. Stir Minwax® Fast-Drying Polyurethane before and during use to eliminate settling on the bottom of the can. Stir to rotate the product from the bottom to the top of the can. NEVER SHAKE.
  5. Apply a THIN coat of Minwax® Fast-Drying Polyurethane using a high-quality natural or foam brush.
  6. For floor projects, use a square buff orbital or disk-type sander with 220 grit sandpaper or the equivalent grit pad or screen (specifically designed for sanding between coats). Do not use a belt or drum-type sander for sanding between coats. Follow the sander manufacturer’s directions for your type of project.
  7. Apply second coat. If third coat is desired, repeat step 6 before application.
  8. After final coat, allow 24 hours before light use.

When used on hardwood floors, use a lambswool or synthetic pad applicator or natural bristle brush and maintain a wet edge to avoid lap marks. For maximum durability, we recommend three coats. Avoid heavy traffic and replacing of furniture for 72 hours after final coat. When replacing furniture, do not slide. Do not install rugs or clean floors for 7 days.

CLEANUP: Use mineral spirits or paint thinner following manufacturer’s safety instructions.

COVERAGE: Approximately 125 square feet per quart.

Note: Above dry times are based on good ventilation, temperature of 77°F and 50% relative humidity. Lower temperature, higher humidity, lack of air movement or application of thick coats will extend drying times. Always test tackiness between coats. Do not sand or re-coat when surface is tacky. Slight ambering may be experienced when Polyurethane is applied over light-colored wood surfaces. Always spot test on an inconspicuous area to ensure satisfactory results. For light-colored wood surfaces, we recommend protecting with Minwax® Polycrylic® Protective Finish or Minwax® Ultimate Floor Finish.

DANGER: Rags, steel wool, other waste soaked with this product, and sanding residue may spontaneously catch fire if improperly discarded. Immediately place rags, steel wool, other waste soaked with this product, and sanding residue in a sealed, water-filled, metal container. Dispose of in accordance with local fire regulations.

CAUTIONS: CONTAINS ALIPHATIC HYDROCARBONS.

Contents are COMBUSTIBLE. Keep away from heat and open flame.

VAPOR HARMFUL. Use only with adequate ventilation. To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches, or dizziness, increase fresh air, or wear respiratory protection (NIOSH approved) or leave the area. Avoid contact with eyes and skin. Wash hands after using. Keep container closed when not in use. Do not transfer contents to other containers for storage.

FIRST AID: In case of eye contact, flush thoroughly with large amounts of water for 15 minutes and get medical attention. For skin contact, wash thoroughly with soap and water. In case of respiratory difficulty, provide fresh air and call physician. If swallowed, call Poison Control Center, hospital emergency room, or physician immediately.|

DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Contains solvents which can cause permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents can be harmful or fatal.

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

DO NOT TAKE INTERNALLY. KEEP OUT OF THE REACH OF CHILDREN.

Aerosol Directions

Interior Use Only

WARNING! If you scrape, sand or remove old paint, you may release lead dust. Lead Is Toxic. Contact the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

  1. The surface must be dry and free of old finishes in poor condition, paint, wax, grease, polish, dirt or other foreign matter.
  2. Sand to obtain a smooth, uniform surface. Remove all dust.
  3. If desired, apply stain, such as Minwax® Wood Finish™ Stain, to unfinished wood surfaces. Follow directions for application instructions and dry times.
  4. Shake Minwax® Fast-Drying Polyurethane vigorously for two minutes. Shake for 10 seconds occasionally during use.
  5. Protect adjacent areas from overspray. Wet overspray can be removed with mineral sprits.
  6. Hold can vertically 12 inches from surface. Depress button fully and spray using an even, sweeping motion with slightly overlapping strokes. On unfinished wood, apply sufficient material to seal open joints, edges and end-grain.
  7. Apply thin coats to avoid runs and sags. Recoat within 2 hours. If unable to do so, wait a minimum of 72 hours, then lightly sand and recoat.
  8. Apply at least three coats on unfinished wood and two coats on surfaces already finished.
  9. After final coat, allow 24 hours before normal use.

Note: Above dry times are based on good ventilation, temperature of 77°F and 50% relative humidity. Lower temperature, higher humidity, lack of air movement or application of thick coats will extend drying times. Slight ambering may be experienced when Polyurethane is applied over light-colored wood surfaces. Always spot test on an inconspicuous area to ensure satisfactory results. Minwax® Polycrylic® Protective Finish is recommended over light-colored wood surfaces.

Nozzle Care

  1. After each use, clear valve by holding can upside down and spraying until only clear gas comes out.
  2. If spray button becomes clogged, wear eye protection, wipe off button opening with lacquer thinner- Do NOT stick pin in spray button opening.

CLEANUP: For easy clean-up, use lacquer thinner following the manufacturer’s safety instructions.

DANGER: Rags, steel wool, other waste soaked with this product, and sanding residue may spontaneously catch fire if improperly discarded. Immediately place rags, steel wool, other waste soaked with this product, and sanding residue in a sealed, water-filled, metal container. Dispose of in accordance with local fire regulations.

CAUTIONS: CONTAINS ALIPHATIC HYDROCARBONS AND KETONES. DANGER! EXTREMELY FLAMMABLE.

Keep away from heat, sparks, and open flame. Vapors will accumulate readily and may ignite explosively. Keep area ventilated during use and until all vapors are gone. DO NOT SMOKE - Extinguish all flames, pilot lights and heaters -Turn off stoves, electric tools and appliances, and any other sources of ignition. CONTENTS UNDER PRESSURE. Avoid prolonged exposure to sunlight or heat from radiators, stoves, hot water and other heat sources that may cause bursting. Do not puncture, incinerate, burn or store above 120°F. Keep upright in a cool, dry place. Do not discard empty can in trash compactor.

VAPOR HARMFUL. Use with adequate ventilation. Avoid continuous breathing of vapor and spray mist. To avoid breathing vapors or spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches, or dizziness, increase fresh air or wear respiratory protection (NIOSH approved) or leave the area. Overexposure may cause numbness in extremities which can persist for some period of time and may be permanent. Avoid contact with eyes and skin. Wash hands after using.

FIRST AID: In case of eye contact, flush thoroughly with large amounts of water for 15 minutes and get medical attention. For skin contact, wash thoroughly with soap and water. In case of respiratory difficulty, provide fresh air and call physician.

DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Contains solvents which can cause permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents can be harmful or fatal.

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

DO NOT TAKE INTERNALLY. KEEP OUT OF THE REACH OF CHILDREN.

CONFORMS TO ASTM D-4236. Contact a physician for more health information.

Sours: https://www.minwax.com/wood-products/clear-protective-finishes/interior/minwax-fastdrying-polyurethane

Interior Clear Protective Finishes

For aerosol directions, click here

WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.

DIRECTIONS:

  1. Surface must be dry and free of old finishes in poor condition, paint, wax, grease, polish, dirt or other foreign matter.
  2. Sand to obtain a smooth uniform surface. Remove all dust with a cloth dampened with mineral spirits.
  3. Stir Minwax® Fast-Drying Polyurethane before and during use to eliminate settling on the bottom of the can. Stir in such a manner as to rotate the product from the bottom to the top of the can. NEVER SHAKE.
  4. Apply a THIN coat of Minwax® Fast-Drying Polyurethane using a high-quality natural or foam brush.
  5. Let dry 4-6 hours. Then lightly sand entire surface with fine sandpaper (220 grit) to ensure an even finish and proper adhesion. Remove all dust.
  6. Apply second coat. If third coat is desired, repeat step 5 before application.
  7. After final coat, allow 24 hours before light use.

When used on wooden floors, use a lambs wool or synthetic pad applicator or natural bristle brush and maintain a wet edge to avoid lap marks. For maximum durability, we recommend three coats. Avoid heavy traffic and replacing of furniture for 72 hours after final coat. When replacing furniture, do not slide. Do not install rugs or clean floors for 7 days.

CLEAN-UP: For easy clean-up use mineral spirits or paint thinner.

COVERAGE: Approximately 125 square feet per quart.

Note: Above dry times are based on good ventilation, temperature of 77°F and 50% relative humidity. Lower temperature, higher humidity, lack of air movement or application of thick coats will extend drying times. Always test tackiness between coats. Do not sand or re-coat when surface is tacky. Slight ambering may be experienced when Polyurethane is applied over light-colored wood surfaces. Always spot test on an inconspicuous area to ensure satisfactory results. For light-colored wood surfaces, we recommend protecting with Minwax® Polycrylic® Protective Finish.

Aerosol Directions

WARNING! If you scrape, sand or remove old paint, you may release lead dust. Lead is Toxic. Contact the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

  1. Protect adjacent areas from overspray. (Wet overspray can be removed with mineral spirits.)
  2. Hold can vertically 12 inches from surface. Depress button fully and spray using an even, sweeping motion with slightly overlapping strokes. On unfinished wood, apply sufficient material to seal open joints, edges and end-grain.
  3. Apply thin coats to avoid runs and sags. Recoat within 2 hours. If unable to do so, wait a minimum of 72 hours, then lightly and sand and recoat.
  4. Apply at least three coats on unfinished wood and two coats on surfaces already finished.
  5. After final coat, allow 24 hours before normal use.

For Semi–Gloss or Satin Sheens Only: Shake can vigorously for two minutes. Shake for 10 seconds occasionally during use.

Note: Above dry times are based on good ventilation temperature of 77° F and 50% relative humidity. Lower temperature, higher humidity, lack of air movement or application of thick coats will extend drying times. Due to ambering qualities, not recommended for use over white or pastel stains. Instead, Minwax® Polycrylic Protective Finish is recommended. Always spot test an inconspicuous area to ensure satisfactory results.

Nozzle Care

  1. After each use, clear valve by holding can upside down and spraying until only clear gas comes out.
  2. 2. If spray button becomes clogged, wear eye protection, wipe off button opening with lacquer thinner- Do NOT stick pin in spray button opening.

Clean-Up: For easy clean-up, use lacquer thinner following the manufacturer’s safety instructions.

CAUTION! CONTAINS KETONES, ALPHATIC HYDROCARBONS, PROPANE, BUTANE. DANGER! EXTREMELY FLAMMABLE. Keep away from heat, sparks, and open flame. Vapors will accumulate readily and may ignite explosively. Keep area ventilated during use and until all vapors are gone. DO NOT SMOKE- Extinguish all flames, pilot lights and heaters. Turn off stoves, electric tools and appliances, and any other sources of ignition. CONTENTS UNDER PRESSURE. Avoid prolonged exposure to sunlight or heat from radiators, stoves, hot water and other heat sources that may cause bursting. Do not puncture, incinerate burn or store above 120°F. Keep upright in a cool, dry place. Do not discard empty can in trash compactor. VAPOR HARMFUL. Use with adequate ventilation. Avoid continuous breathing of vapor and spray mist. To avoid breathing vapors or spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches, or dizziness, increase fresh air, or wear respiratory protection (NIOSH approved) or leave the area. Avoid contact with eyes and skin. Wash hands after using. FIRST AID: In case of eye contact, flush thoroughly with large amounts of water for 15 minutes and get medical attention. For skin contact, wash thoroughly with soap and water. In case of respiratory difficulty, provide fresh air and call physician. DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Contains solvents which can cause permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents can be harmful or fatal. WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. DO NOT TAKE INTERNALLY. KEEP OUT OF THE REACH OF CHILDREN. Conforms to ASTM D-4236. Contact a physician for more health information.

Sours: https://www.minwax.ca/wood-products/interior-clear-protective-finishes/minwax-fastdrying-polyurethane
  1. South fork hotels
  2. 06 ford f150 mpg
  3. 1st choice virgin hair
  4. Hill city idaho weather
  5. Nissan rogue 2010 accessories

Directions

Instrucciones en Español

Interior Use Only

WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more information, call the National Lead Information Center at LEAD (in US) or contact your local health authority.

Directions:

  1. Surface must be dry and free of old finishes in poor condition, paint, wax, grease, polish, dirt or other foreign matter.
  2. Sand to obtain a smooth uniform surface. Remove all dust.
  3. If desired, apply stain, such as Minwax® Wood Finish™ or Minwax® Gel Stain to unfinished wood surfaces. Follow directions for application and dry times.
  4. Stir Minwax® Fast-Drying Polyurethane before and during use to eliminate settling on the bottom of the can. Stir to rotate the product from the bottom to the top of the can. NEVER SHAKE.
  5. Apply a THIN coat of Minwax® Fast-Drying Polyurethane using a high-quality natural or foam brush.
  6. Let dry hours. Then lightly sand entire surface with fine sandpaper ( grit) to ensure an even finish and proper adhesion. Remove all dust.
  7. For floor projects, use a square buff orbital or disk-type sander with grit sandpaper or the equivalent grit pad or screen (specifically designed for sanding between coats). Do not use a belt or drum-type sander for sanding between coats. Follow the sander manufacturer's directions for your type of project.
  8. Apply a second coat. If a third coat is desired, repeat step 6 before application.
  9. After final coat, allow 24 hours before light use.

When used on hardwood floors, use a lambswool or synthetic pad applicator or natural bristle brush and maintain a wet edge to avoid lap marks. For maximum durability, we recommend three coats. Avoid heavy traffic and replacing of furniture for 72 hours after final coat. When replacing furniture, do not slide. Do not install rugs or clean floors for 7 days.

CLEANUP: Use mineral spirits or paint thinner following manufacturer's safety instructions.

COVERAGE: Approximately square feet per gallon.

Note: Dry times and coverage rates are based on good ventilation, temperature of 77°F and 50% relative humidity. Lower temperature, higher humidity, lack of air movement or application of thick coats will extend dry time. Always test tackiness between coats. Do not sand or re-coat when surface is tacky. Slight ambering may be experienced when Polyurethane is applied over light-colored wood surfaces. Always spot test on an inconspicuous area to ensure satisfactory results. For light-colored wood surfaces, we recommend protecting with Minwax® Polycrylic® Protective Finish or Minwax® Ultimate Floor Finish.

DANGER: Rags, steel wool, other waste soaked with this product, and sanding residue may spontaneously catch fire if improperly discarded. Immediately place rags, steel wool, other waste soaked with this product, and sanding residue in a sealed, water-filled, metal container. Dispose of in accordance with local fire regulations.

CAUTIONS: CONTAINS ALIPHATIC HYDROCARBONS.

Contents are COMBUSTIBLE. Keep away from heat and open flame.

VAPOR HARMFUL. Use only with adequate ventilation. To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches, or dizziness, increase fresh air, or wear respiratory protection (NIOSH approved) or leave the area. Avoid contact with eyes and skin. Wash hands after using. Keep container closed when not in use. Do not transfer contents to other containers for storage.

FIRST AID: In case of eye contact, flush thoroughly with large amounts of water for 15 minutes and get medical attention. For skin contact, wash thoroughly with soap and water. In case of respiratory difficulty, provide fresh air and call physician. If swallowed, call Poison Control Center, hospital emergency room, or physician immediately.|

DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Contains solvents which can cause permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents can be harmful or fatal.

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

DO NOT TAKE INTERNALLY. KEEP OUT OF THE REACH OF CHILDREN.

Sours: https://www.minwax.com/wood-products/clear-protective-finishes/interior/minwax-fastdrying-polyurethanevoc-compliant

Directions

Instrucciones en Español
Instructions for using Minwax® Fast-Drying Polyurethane.

For aerosol directions, click here

Interior Use Only

WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more information, call the National Lead Information Center at LEAD (in US) or contact your local health authority.

Directions:

  1. Surface must be dry and free of old finishes in poor condition, paint, wax, grease, polish, dirt or other foreign matter.
  2. Sand to obtain a smooth uniform surface. Remove all dust with a cloth dampened with mineral spirits.
  3. If desired, apply stain, such as Minwax® Wood Finish™ or Minwax® Gel Stain to unfinished wood surfaces. Follow directions for application and dry times.
  4. Stir Minwax® Fast-Drying Polyurethane before and during use to eliminate settling on the bottom of the can. Stir to rotate the product from the bottom to the top of the can. NEVER SHAKE.
  5. Apply a THIN coat of Minwax® Fast-Drying Polyurethane using a high-quality natural or foam brush.
  6. For floor projects, use a square buff orbital or disk-type sander with grit sandpaper or the equivalent grit pad or screen (specifically designed for sanding between coats). Do not use a belt or drum-type sander for sanding between coats. Follow the sander manufacturer’s directions for your type of project.
  7. Apply second coat. If third coat is desired, repeat step 6 before application.
  8. After final coat, allow 24 hours before light use.

When used on hardwood floors, use a lambswool or synthetic pad applicator or natural bristle brush and maintain a wet edge to avoid lap marks. For maximum durability, we recommend three coats. Avoid heavy traffic and replacing of furniture for 72 hours after final coat. When replacing furniture, do not slide. Do not install rugs or clean floors for 7 days.

CLEANUP: Use mineral spirits or paint thinner following manufacturer’s safety instructions.

COVERAGE: Approximately square feet per quart.

Note: Above dry times are based on good ventilation, temperature of 77°F and 50% relative humidity. Lower temperature, higher humidity, lack of air movement or application of thick coats will extend drying times. Always test tackiness between coats. Do not sand or re-coat when surface is tacky. Slight ambering may be experienced when Polyurethane is applied over light-colored wood surfaces. Always spot test on an inconspicuous area to ensure satisfactory results. For light-colored wood surfaces, we recommend protecting with Minwax® Polycrylic® Protective Finish or Minwax® Ultimate Floor Finish.

DANGER: Rags, steel wool, other waste soaked with this product, and sanding residue may spontaneously catch fire if improperly discarded. Immediately place rags, steel wool, other waste soaked with this product, and sanding residue in a sealed, water-filled, metal container. Dispose of in accordance with local fire regulations.

CAUTIONS: CONTAINS ALIPHATIC HYDROCARBONS.

Contents are COMBUSTIBLE. Keep away from heat and open flame.

VAPOR HARMFUL. Use only with adequate ventilation. To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches, or dizziness, increase fresh air, or wear respiratory protection (NIOSH approved) or leave the area. Avoid contact with eyes and skin. Wash hands after using. Keep container closed when not in use. Do not transfer contents to other containers for storage.

FIRST AID: In case of eye contact, flush thoroughly with large amounts of water for 15 minutes and get medical attention. For skin contact, wash thoroughly with soap and water. In case of respiratory difficulty, provide fresh air and call physician. If swallowed, call Poison Control Center, hospital emergency room, or physician immediately.|

DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Contains solvents which can cause permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents can be harmful or fatal.

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

DO NOT TAKE INTERNALLY. KEEP OUT OF THE REACH OF CHILDREN.

Aerosol Directions

Interior Use Only

WARNING! If you scrape, sand or remove old paint, you may release lead dust. Lead Is Toxic. Contact the National Lead Information Hotline at LEAD or log on to www.epa.gov/lead.

  1. The surface must be dry and free of old finishes in poor condition, paint, wax, grease, polish, dirt or other foreign matter.
  2. Sand to obtain a smooth, uniform surface. Remove all dust.
  3. If desired, apply stain, such as Minwax® Wood Finish™ Stain, to unfinished wood surfaces. Follow directions for application instructions and dry times.
  4. Shake Minwax® Fast-Drying Polyurethane vigorously for two minutes. Shake for 10 seconds occasionally during use.
  5. Protect adjacent areas from overspray. Wet overspray can be removed with mineral sprits.
  6. Hold can vertically 12 inches from surface. Depress button fully and spray using an even, sweeping motion with slightly overlapping strokes. On unfinished wood, apply sufficient material to seal open joints, edges and end-grain.
  7. Apply thin coats to avoid runs and sags. Recoat within 2 hours. If unable to do so, wait a minimum of 72 hours, then lightly sand and recoat.
  8. Apply at least three coats on unfinished wood and two coats on surfaces already finished.
  9. After final coat, allow 24 hours before normal use.

Note: Above dry times are based on good ventilation, temperature of 77°F and 50% relative humidity. Lower temperature, higher humidity, lack of air movement or application of thick coats will extend drying times. Slight ambering may be experienced when Polyurethane is applied over light-colored wood surfaces. Always spot test on an inconspicuous area to ensure satisfactory results. Minwax® Polycrylic® Protective Finish is recommended over light-colored wood surfaces.

Nozzle Care

  1. After each use, clear valve by holding can upside down and spraying until only clear gas comes out.
  2. If spray button becomes clogged, wear eye protection, wipe off button opening with lacquer thinner- Do NOT stick pin in spray button opening.

CLEANUP: For easy clean-up, use lacquer thinner following the manufacturer’s safety instructions.

DANGER: Rags, steel wool, other waste soaked with this product, and sanding residue may spontaneously catch fire if improperly discarded. Immediately place rags, steel wool, other waste soaked with this product, and sanding residue in a sealed, water-filled, metal container. Dispose of in accordance with local fire regulations.

CAUTIONS: CONTAINS ALIPHATIC HYDROCARBONS AND KETONES. DANGER! EXTREMELY FLAMMABLE.

Keep away from heat, sparks, and open flame. Vapors will accumulate readily and may ignite explosively. Keep area ventilated during use and until all vapors are gone. DO NOT SMOKE - Extinguish all flames, pilot lights and heaters -Turn off stoves, electric tools and appliances, and any other sources of ignition. CONTENTS UNDER PRESSURE. Avoid prolonged exposure to sunlight or heat from radiators, stoves, hot water and other heat sources that may cause bursting. Do not puncture, incinerate, burn or store above °F. Keep upright in a cool, dry place. Do not discard empty can in trash compactor.

VAPOR HARMFUL. Use with adequate ventilation. Avoid continuous breathing of vapor and spray mist. To avoid breathing vapors or spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches, or dizziness, increase fresh air or wear respiratory protection (NIOSH approved) or leave the area. Overexposure may cause numbness in extremities which can persist for some period of time and may be permanent. Avoid contact with eyes and skin. Wash hands after using.

FIRST AID: In case of eye contact, flush thoroughly with large amounts of water for 15 minutes and get medical attention. For skin contact, wash thoroughly with soap and water. In case of respiratory difficulty, provide fresh air and call physician.

DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Contains solvents which can cause permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents can be harmful or fatal.

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

DO NOT TAKE INTERNALLY. KEEP OUT OF THE REACH OF CHILDREN.

CONFORMS TO ASTM D Contact a physician for more health information.

Sours: https://www.minwax.com/wood-products/clear-protective-finishes/interior/minwax-fastdrying-polyurethane

Drying minwax polyurethane fast

Directions

Instrucciones en Español

Interior Use Only

WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.

Directions:

  1. Surface must be dry and free of old finishes in poor condition, paint, wax, grease, polish, dirt or other foreign matter.
  2. Sand to obtain a smooth uniform surface. Remove all dust.
  3. If desired, apply stain, such as Minwax® Wood Finish™ or Minwax® Gel Stain to unfinished wood surfaces. Follow directions for application and dry times.
  4. Stir Minwax® Fast-Drying Polyurethane before and during use to eliminate settling on the bottom of the can. Stir to rotate the product from the bottom to the top of the can. NEVER SHAKE.
  5. Apply a THIN coat of Minwax® Fast-Drying Polyurethane using a high-quality natural or foam brush.
  6. Let dry 4-6 hours. Then lightly sand entire surface with fine sandpaper (220 grit) to ensure an even finish and proper adhesion. Remove all dust.
  7. For floor projects, use a square buff orbital or disk-type sander with 220 grit sandpaper or the equivalent grit pad or screen (specifically designed for sanding between coats). Do not use a belt or drum-type sander for sanding between coats. Follow the sander manufacturer's directions for your type of project.
  8. Apply a second coat. If a third coat is desired, repeat step 6 before application.
  9. After final coat, allow 24 hours before light use.

When used on hardwood floors, use a lambswool or synthetic pad applicator or natural bristle brush and maintain a wet edge to avoid lap marks. For maximum durability, we recommend three coats. Avoid heavy traffic and replacing of furniture for 72 hours after final coat. When replacing furniture, do not slide. Do not install rugs or clean floors for 7 days.

CLEANUP: Use mineral spirits or paint thinner following manufacturer's safety instructions.

COVERAGE: Approximately 600 square feet per gallon.

Note: Dry times and coverage rates are based on good ventilation, temperature of 77°F and 50% relative humidity. Lower temperature, higher humidity, lack of air movement or application of thick coats will extend dry time. Always test tackiness between coats. Do not sand or re-coat when surface is tacky. Slight ambering may be experienced when Polyurethane is applied over light-colored wood surfaces. Always spot test on an inconspicuous area to ensure satisfactory results. For light-colored wood surfaces, we recommend protecting with Minwax® Polycrylic® Protective Finish or Minwax® Ultimate Floor Finish.

DANGER: Rags, steel wool, other waste soaked with this product, and sanding residue may spontaneously catch fire if improperly discarded. Immediately place rags, steel wool, other waste soaked with this product, and sanding residue in a sealed, water-filled, metal container. Dispose of in accordance with local fire regulations.

CAUTIONS: CONTAINS ALIPHATIC HYDROCARBONS.

Contents are COMBUSTIBLE. Keep away from heat and open flame.

VAPOR HARMFUL. Use only with adequate ventilation. To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches, or dizziness, increase fresh air, or wear respiratory protection (NIOSH approved) or leave the area. Avoid contact with eyes and skin. Wash hands after using. Keep container closed when not in use. Do not transfer contents to other containers for storage.

FIRST AID: In case of eye contact, flush thoroughly with large amounts of water for 15 minutes and get medical attention. For skin contact, wash thoroughly with soap and water. In case of respiratory difficulty, provide fresh air and call physician. If swallowed, call Poison Control Center, hospital emergency room, or physician immediately.|

DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Contains solvents which can cause permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents can be harmful or fatal.

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

DO NOT TAKE INTERNALLY. KEEP OUT OF THE REACH OF CHILDREN.

Sours: https://www.minwax.com/wood-products/clear-protective-finishes/interior/minwax-fastdrying-polyurethane-350-voc-compliant
Speeding Up The Drying Time-Oil Based Finish

But gin is still in bulk. - Well, okay. Betting.

Now discussing:

Tongue tirelessly licked the head, then drilled into its crack. She then accelerated the pace to incredible, then suddenly froze, completely immersing my penis in her mouth, and at the same time she covered it so. Tightly that it seemed now that she was about to suck all my sperm up, not even letting me finish. - Well, that's all - I can no longer - with these words she abruptly straightened up and looked in my direction.



2275 2276 2277 2278 2279