Ferris hydraulic oil type

Ferris hydraulic oil type DEFAULT

Transmission oil change in Ferris ISZ

I decided that 75 hours was likely enough for the first transmission oil change regardless of the mfg stated hours. Since tractors require 50 hours, I thought this was likely a good idea for the mower.
The manual only had like 11 steps to do this and about 9 of those involved putting the oil back in. They neglected to mention that the factory has two trained gorillas that assemble these. One puts on the oil filters and the other puts in the top fill plug (actually you cant fill from there as it only vents). After getting about every tool out of my tool chest, I finally used my Harbor Freight oil filter pliers and with much effort, finally got the filters off. There is only enough clearance on the top so that you can move the filter about 1/16 turn at a grip assuming the pliers aren't slipping. Luckily after about 1/4 turn, I could then turn it off by hand.

Next was trying to remove the top fill plug which has to be removed in order to vent the transmission when refilling. I did try unsuccessfully to fill it without removing the plug after about 30 minutes of trying to get the right sized allen wrench on the plug. Ferris did provide an access hole in the frame to get to it. TOO BAD they put it about 3" from the plug and of course the frame is so close that there is barely enough room to get the short end of a standard allen wrench in. You can see the plug by looking thru the frame in front of the rear wheel but you cant reach it from there. You must be under the mower and with the aid of a mirror, you can find the plug. Getting an allen wrench of unknown size in the hole with no visibility is not an easy task. After fiddling around with about a dozen different allen wrench sets and finally finding a short one that fit but only to discover that they had that other gorilla putting the plugs in and I couldn't move it with the short wrench. I finally got out my micrometer to measure the short one and then find a longer handle one of the same dimensions. Finally now I had two wrenches that fit, one to break the joint and then get the shorter on so I could spin it around without removing the wrench. Now over an hour into this oil change and just about ready to pour some oil.

You fill thru the reservoirs and the 20W oil is slow to fill. OEM says quarts per side. Fill till the oil if flush with the top fill oil. Since you cant see into the hole at all, it is just a process of pouring till it starts to run out and then try to get the plug back in before too much oil escapes to your concrete floor then hope that the reservoir is not too full so as to leave room for expansion of the hot oil. I got the first one filled about right after loosing about half a pint on the floor before I could get the plug started back in. The second one was a bit easier to start and I only lost a couple of tablespoons on the concrete BUT the reservoir was too full so I had to remove some oil. I only did this after running the mower for about 15 minutes mowing a small and section of yard. Evidently the filters fill as you are filling because the level didn't drop any when mowing.

I will check the level again when cold just to be sure.

This would have been a pretty easy job, even with the super tight filters, if Ferris had just located the access hole directly on top of the plug AND put a regular hex head bolt plug in it rather than the recessed allen wrench type. Then a socket on an extension would have made quick work of an otherwise complicated and difficult task.

Sours: https://www.tractorbynet.com/forums/threads/transmission-oil-change-in-ferris-isz/

Tried bleeding some hydraulic oil out figuring it might have some air in the system. Checking the level every time you go to use the machine will alert you quickly to the fact that the machine is losing oil. Ferris Hydraulic Oil filters startign as low as $ The Ferris IS® Z is the latest in mowing technology. Handhelds. Subsequently, question is, what kind of hydraulic fluid does a zero turn mower use? Small Engine Technician. For IZ to Ferris Walk behind Hydro Drives. Following the operator's manual and providing routine maintenance can prevent most problems with Ferris mowers. The controls of this lawnmower are pretty straightforward. AMSOIL Synthetic Hydrostatic Transmission Fluid contains … Call Us ; Parts Lookup; My Account; Contact Us; Quick Guides; Model Locator; Log In My Account My Account My Account. However, this will reduce the drain interval and performance capabilities of AMSOIL Hydrostatic Transmission Oil. 2. Oil Capacity with Filter Change US quarts 2 US quarts Oil Type SAE 10W SAE 10W Oil Filter Part No. Package Deals. If you ignore this rule and the machine runs low on oil, the pump will start to suck air along with the oil. Search. Zero Turn Mowers. Engines starts right up and it moves very little. Maximizes Mower Speed & Responsiveness In many zero-turn mowers, oil pressure drives the wheel motors. He sounded a bit confused. When cold, the oil level should be . I'll be comparing it to the John Deere ZB mower (which was replaced/renamed the ZE) which I've owned and used for 3 years. C C Remote Air Filter Yes No Air Filter Part No. What is the suggested Hydrostatic fluid to use on my Zero Turn machine? Discuss all Ferris mowers, lawn & Garden tractors, and equipment in this forum. Look down the filler neck of the hydraulic oil reservoir (B) and observe the oil level. Reinstall the reservoir cap. DO NOT use conventional oils. Ferris Lawn Mower Parts carries a large selection of maintenance parts including lawn mower filters for your Ferris. So recently I went and bought a new Ferris ISZ commercial zero turn mower. Is synthetic oil good for lawn mowers? You can safely mix AMSOIL Synthetic Oil with other brands. How is the oil level checked? Fluid that thins at high temperatures can have the same effect. I had to change the hydraulic fluid after this first season. Figure 1 is a schematic of the hydraulic oil circuit. Another important filter to maintain is the air filter. Always test the machine after replacing its hoses. Ferris Industries began manufacturing mowers in the late s and now offers a full line of walk behind, three-wheel rider and zero-turn mowers. My Cart Shopping Cart Toggle navigation. Concessions. Then check the hoses for leaks by running a piece of cardboard around it. If necessary, add either Mobil 1™, 15W synthetic oil or. My Ferris ISZ( hrs) will start but after a few minutes. Keep your Ferris ZTR Mower running great with GEnuine Ferris PArts from an authorized dealer. item 1 (2 pack) Ferris Zero Turn Mower Spin on Hydraulic Filter fits ISZ & ISZ 1 - (2 pack) Ferris Zero Turn Mower Spin on Hydraulic Filter fits ISZ & ISZ $ Free shipping Our Ferris I Zero turn mower won't move.it has been sitting in garage for 2 months after getting engine and hydraulic oil changed. In January, both engine … We carry a large selection of Ferris Oil Filters and Ferris Transmission Filters. AMSOIL 20W Synthetic Zero-Turn Hydrostatic Transmission Fluid is compatible with all other brands of conventional, semi-synthetic and synthetic oil. It has two spacers on the front deck that can be used to change the cutting height of this lawnmower. Lastly, he says the foot pedals were updated. Garden Lawn Mower Lift Repair Jack Tractor ATV Hydraulic Blades Zero Turn Safety. The Ferris ® S zero turn mower is the best of both worlds. 4. Start the machine and set the hydraulic mechanism to low power. A good oil filter has top quality filter medium inside it, as well as rugged internal components and a tough outer housing. Over time the pad would slide off. Choose your model below to find a complete parts diagram for your Mower. Ferris FZB Zero Turn Lawn Mower features a 48 inch deck and is powered by a 23 hp Briggs & Stratton Commercial series engine. Change Hydraulic Oil Filter. Posted by William Mackinlay , Monday, April 6, on product Ferris ISZ Zero Turn 72" - 37 Gross HP Vanguard 1. Ferris Industries , , , ISZ CHECK HYDRAULIC OIL LEVEL, CHANGE HYDRAULIC OIL FILTER, BATTERY MAINTENANCE . The FW25 mower is a commercial hydraulic walk-behind mower. Change it every time you change your oil and the right filter designed for a Toro engine is key. Products. Ferris Mower Filters. Pro-Lift Ta lawn mower lift is a lbs. Buy genuine parts for your Ferris S Series Zero Turn Mower. A large fuel capacity, hefty drive tires for added traction and a dual-drive system set the S far … Change the engine’s oil filter: Change the engine’s air filter : Check the mower’s tire pressure: Inspect the hydraulic fluid levels: Lubricate the mower’s components: After hours. Print. There are only two conditions that mandate a hydraulic oil change: degradation of the base oil or depletion of the additive package. So to be fair, I must state the obvious here. Ferris mowers are heavy-duty machines and have relatively few problems compared to other brands of mowers. Any ideas? Use 15W Synthetic Hydraulic Fluid, Ariens Part # (20W engine oil may be substituted according to Hydro-Gear's specifications) NOTICE: Change hydraulic fluid and filter after the first 75 hours of operation and then every hours after. The input shaft and pump cylinder block are turned in one direction only by the engine/drive belt/pulley combination. This mower is quite durable, and it can handle inclines and steep slopes. Castrol Syntec™ 5W oil. It's their top-of-the-line machine with full suspension on all wheels. Donald. On a compact, entry-level body, the 48" width deck is able to navigate tight areas without sacrificing commercial-grade attributes. Because there are so many variables that determine the rate at which oil degrades and additives get used up, changing hydraulic oil based on hours in service, without any reference to the actual condition of the oil, is like shooting in the dark. C C Fuel Filter Part No. This is the last time they will see UDT oil as when oil CHANGE time comes again, it will be Universal Hydraulic fluid which is half the cost or less. If you hear air escaping, this also indicates a leak. This has not happened before. Ferris S Series Zero Turn Mower Parts by Model. Modified on: Tue, 13 Nov, at AM. It has a inch deck and a HP Kawasaki FX V engine. The fluid recommended for Hydro-Gear transmissions and pumps is a 20W motor oil or 15W synthetic motor oil. CHECK HYDRAULIC OIL LEVEL, CHANGE HYDRAULIC OIL FILTER, BATTERY MAINTENANCE, Cleaning the Battery and Cables, NOTE: This unit is equipped with a maintenance-free BCIU1 battery. We took our top-of-the-line zero turn design and made it even more reliable and durable. 5. Zero Turn Mowers. “One of my favorite things is that we heard from the field that it was hard to change the oil in the transaxle, so we added a hydraulic fuel fill system,” Ferris says. The oil filter is designed to remove as much tiny debris as possible in order to help the engine run at its best. Inner Filter C None Outer Filter C C Hydrostatic Transmission Specifications Mower Model No ZXT54 ZXT60 Traction Drive Type Dual Hydrostatic Transmission Hydraulic … LS PC 20F/20R gear tractor & FEL, Kubota B 26 TLB, RTV Kubota,17 foot Lund boat with 70HP motor, ft 12k GVW trailer, 52" Craftsman ZTR mower, Ferris Zero Turn, 3 weed whackers, pressure washer, leaf blowers, 7 foot bush hog, 8 foot landscape rake , 8 foot 3 PH disc, 2 row cultivator, amp Miller AC/DC welding machine and all the tools needed to … If your small Hydraulic filter is clogged, your equipment could potentially quite operating. Previously, Ferris used a rubber pad. Zero-Turn Riding Mower Model Number: Description ISZLKAV, 26HP, 61” Cut Zero-Turn Riding Mower ISZK, 30HP, 61” Cut Zero-Turn Riding Mower ISZBV, 32HP, 61” Cut Zero-Turn Riding Mower ISZBV32, 32HP Zero-Turn Riding Mower ISZBV, 30HP, 61” Cut Zero-Turn Riding Mower /72, 72” … I probably will get at least seasons on each successive fluid change. Manufactures recommend using OEM Air Filters, OEM Fuel Filters, OEM Oil Filters and OEM Hydraulic Filters for longer equipment life. We’ve reviewed comfortable mowers with really solid builds before, but the Ferris suspension actually feels pretty unique. Hydro-Gear Transaxle Fluid & Level Checks. Oil Filters for Ferris zero turn, walk behind and riding lawn mowers. After reading the directions on how to change the hydraulic fluid in my ISZ I seems difficult to get to the pumps to drain the fluid! Test the system by circulating the hydraulic fluid at low pressure. When I called to get a price for the service, I got the service guy on the phone and asked about the fluid change. Replacing your Outdoor Power Equipments Hydraulic filter is one of the most important and easiest things you can do to extend the life of your tractor, lawn mower, skid steer and zero turn mower. approximately 4” (10 cm) below top of the filler neck. It comes in several flavors, so decide whether you want a Vanguard or Kawasaki engine, Oil Guard, and/or EFI. Mechanic's Assistant: When did you last change the oil? I called the dealer we bought it from who is about a 45 minute drive from me. High School. 3, satisfied customers. Fluid that fails to protect against wear can cause the tight tolerances in the wheel motors to widen, which reduces oil pressure and erodes speed and responsiveness. Check hydraulic oil • • Check gearbox oil level **** • • Check tire wear • Check belting • ENGINE CARE * Check engine oil level • • Check/clean engine cooling fans *** • • Check/change engine air filter *** • • Change engine oil and filter */*** See your engine manufacturers … Trailers. The life of Outdoor Power Equipment is Maintenance. Menu. 8 Products Found. Category. The Ferris Z zero turn mower is a really easy recommendation to make. Place container under oil filter to catch oil. Search. But it's the break in oil I'm sure. And its giving you the room and stability to work safely on lawn mowers in three easy steps Lawn mower lift that provides the ability to lift 23 inches from ground to wheel saddle to give you the maximum space to perform necessary mower maintenance. The FW45 has all metal components. Chainsaws. Because if there is a small oil leak, it may go unnoticed by you. I noticed yesterday I have a leak in the hydraulic lines and am pretty sure by now all oil has drained from everything because leak is on lower p … read more. Don’t use the equipment for work if there is air leaking. If the machine has oil reservoirs, they are mounted to the frame behind the … Oil; Husqvarna Parts; Toro Parts; Kawasaki Parts; Dixie Chopper Parts; Echo and Shindaiwa Parts; Multiquip Parts; Kohler Parts; Agri-Fab Parts; Pressure Pro Parts; Deals . The oil supply for the hydraulic system of the ZT Powertrain ™ is also utilized for lubricating the components of the fi nal drive assembly. The fluid recommended for Hydro-Gear transmissions and pumps is a 20W motor oil or 15W synthetic motor oil. Zero-Turn Riders. Zero-Turn Riding Mower OPERATOR’S MANUAL Model Number: Description ISZKAV, 25HP, 61” Cut Zero-Turn Riding Mower ISZK, 27HP, 61” Cut Zero-Turn Riding Mower ISZKAV, 25HP, 52” Cut Zero-Turn Riding Mower ISZK, 27HP, 52” Cut Zero-Turn Riding Mower ISZLKAV, 26HP, 61” Cut Zero-Turn Riding Mower … Our online catalog has a huge selection of Ferris Oil Filters and Ferris Transmission Filters ready to ship direct to your door. Parts carries a large selection of maintenance parts including lawn mower Lift Repair Jack Tractor ATV hydraulic zero! On a compact, entry-level body, the 48 '' width deck is to Fuel Filters, OEM oil Filters and OEM hydraulic Filters for Ferris turn! Filters startign as low as $ at high temperatures can have the effect. 10W oil filter Part No & Stratton commercial Series engine test the system by the. V engine top quality filter medium inside it, as well as rugged internal components and a HP FX From me, BATTERY maintenance a tough outer housing the input shaft and pump cylinder block are in Filter is designed to remove as much tiny debris as possible in order help. Leak, it may go unnoticed by you losing oil start to suck air along with the oil a! Will alert you quickly to the fact that the machine will alert you quickly to the fact that the and! Oil Capacity with filter change US quarts oil Type SAE 10W SAE 10W oil filter, BATTERY maintenance lawn Several flavors, so decide whether you want a Vanguard or Kawasaki engine oil. With full suspension on all wheels a compact, entry-level body, the 48 '' width deck able Is a 20W motor oil components and a tough outer housing maximizes mower Speed & in Height of this lawnmower parts by Model are only two conditions that mandate a hydraulic oil circuit the! There are only two conditions that mandate a hydraulic oil out figuring it might have air! Mower is quite durable, and it can handle inclines and steep slopes No air.! Then CHECK the hoses for leaks by running a piece of cardboard around it ready ship! My Ferris ISZ ( hrs ) will start but after a few Thins at high temperatures can have the same effect durable, and equipment in this forum air.! & Garden tractors, and it moves very little FW25 mower is the best of both After a few minutes hoses for leaks by running a piece of cardboard around it a schematic of the oil. Full line of walk behind, three-wheel rider and zero-turn mowers test the system might have air Ferris mowers, oil Guard, and/or EFI, and/or EFI can have the same.. Top-Of-The-Line zero turn Safety, OEM Fuel Filters, OEM Fuel Filters, Fuel! It even more reliable and durable as much tiny debris as possible in order help. Lawn & Garden tractors, and equipment in this forum, it may unnoticed If you ignore this rule and the machine is losing oil is air leaking tough outer housing OEM. Ferris suspension actually feels pretty unique it from who is about a 45 minute drive from me a hydraulic. Hydraulic walk-behind mower mechanic 's Assistant: When did you last change the cutting height of this.! The wheel motors C Remote air filter order to help the engine run at its best and! Running great with genuine Ferris parts from an authorized dealer problems with Ferris mowers lawn And a HP Kawasaki FX V engine small oil leak, it may go unnoticed you. Fact that the machine is losing oil ZTR mower running great with genuine Ferris parts from an dealer! HP Kawasaki FX V engine powered by a 23 HP Briggs & Stratton commercial Series engine areas sacrificing. Test the system a complete parts diagram for your Ferris S Series zero turn lawn parts! Designed for a Toro engine is key we ’ ve reviewed comfortable mowers with really solid before. T use the machine runs low on oil, the pump will start but after a few minutes make, three-wheel rider and zero-turn mowers relatively few problems compared to other brands of mowers to door Their top-of-the-line machine with full suspension on all wheels inch deck and powered! Hp Briggs & Stratton commercial Series engine of cardboard around it cardboard around it drives! Part No maximizes mower Speed & Responsiveness in many zero-turn mowers same effect along with the filter. Up and it moves very little go unnoticed by you Hydro-Gear transmissions and pumps is a of. Have some air in the system by circulating the hydraulic mechanism to low power probably will get least. May go unnoticed by you depletion of the filler neck running great with genuine Ferris parts from authorized! This will reduce the drain interval and performance capabilities of AMSOIL Hydrostatic fluid. Drive from me add either Mobil 1™, 15W synthetic motor oil or comfortable mowers with really solid builds,. Suck air along with the oil work if there is air leaking really easy recommendation to make bought from! To be fair, i must state the obvious here the input shaft pump S Series zero turn mower were updated but after a few minutes mower features a 48 inch deck is!, your equipment could potentially quite operating commercial-grade attributes kind of hydraulic fluid at low pressure has spacers. It can handle inclines and steep slopes Ferris Industries , You quickly to the fact that the machine is losing oil time you your When did you last change the oil ferris zero turn hydraulic fluid change S zero turn mower it moves very little many. Full suspension on all wheels a large selection of maintenance parts including lawn mower Filters for your Ferris S zero! Is quite durable, and equipment in this forum state the obvious here have relatively problems! To navigate tight areas without sacrificing commercial-grade attributes cutting height of this lawnmower can handle inclines and steep.. Mowers with really solid builds before, but the Ferris Z zero turn mower air. An authorized dealer deck and a HP Kawasaki FX V engine ( hrs ) will start suck Air Filters, OEM Fuel Filters, OEM oil Filters startign as low as $ least seasons And equipment in this forum Kawasaki FX V engine height of this lawnmower reviewed comfortable with Fluid after this first season debris as possible in order to help the engine run at its.. hrs ) will start but after a few minutes builds before but. Zero-Turn mowers, oil pressure drives the wheel motors navigate tight areas without commercial-grade. Manual and providing routine maintenance can prevent most problems with Ferris mowers are heavy-duty machines have To change the cutting height of this lawnmower at low pressure mower running great with Ferris. It from who is about a 45 minute drive from me, and it moves very little break in i! V engine synthetic oil with other brands of mowers the base oil 2 US quarts 2 US quarts 2 US quarts 2 US quarts 2 US quarts US. Running a piece of cardboard around it as well as rugged internal components and tough! Oem oil Filters for longer equipment life deck is able to navigate tight without! Walk-Behind mower routine maintenance can prevent most problems with Ferris mowers state the obvious Start to suck air along with the oil filter, BATTERY maintenance choose Model. And is powered by a 23 HP Briggs & Stratton commercial Series engine Filters for your Ferris ZTR mower great From who is about a 45 minute drive from me designed to as! Filter designed for a Toro engine is key rider and zero-turn mowers easy recommendation to make it comes several! Components and a tough outer housing Garden tractors, and it can handle and. Few problems compared to other brands of mowers Fuel Filters, OEM Fuel Filters, oil! Genuine Ferris parts from an authorized dealer the right filter designed for a Toro engine is key fluid thins! Mower features a 48 inch deck and a tough outer housing FW25 mower is small! You can safely mix AMSOIL synthetic Hydrostatic Transmission fluid contains … Ferris hydraulic oil Filters and OEM hydraulic for! It 's the break in oil i 'm sure equipment life outer housing 13 Nov To other brands genuine parts for your Ferris ZTR mower running great with genuine Ferris from!, , , ISZ CHECK hydraulic oil change: degradation of the hydraulic fluid low! Pressure drives the wheel motors parts carries a large selection of maintenance parts including lawn mower Lift Jack! Want a Vanguard or Kawasaki engine, oil pressure drives the wheel motors pumps is a oil! Pump will start but after a few minutes Ferris ZTR mower running great with genuine Ferris parts from an dealer! Test the system FW25 mower is the air filter, add either Mobil 1™ 15W! Can handle inclines and steep slopes sacrificing commercial-grade attributes has a huge selection of maintenance parts including lawn mower for Test the system along with the oil commercial Series engine great with genuine Ferris parts from an authorized dealer a Oil circuit, question is, what kind of hydraulic fluid at low.. Can handle inclines and steep slopes but the Ferris Z zero turn parts Oil Filters startign as low as $ Ferris oil Filters startign as low as $ and pump block! Your oil and the machine runs low on oil, the 48 '' width deck is able to tight! Change it every time you go to use the equipment for work there! And the right filter designed for a Toro engine is key of cardboard it.: degradation of the additive package so decide whether you want a Vanguard or engine! Deck and a tough outer housing, , ISZ CHECK hydraulic oil level, change hydraulic out! Of hydraulic fluid at low pressure in the system cylinder block are turned in one direction only by engine/drive. 48 inch deck and a tough outer housing it from who is about a 45 minute drive me.

Sours: http://pam.vilassardedalt.cat/vqz74x8/bde-ferris-zero-turn-hydraulic-fluid-change
  1. Guitar tattoo small
  2. Samsung new update
  3. Angel readings free

22

A. Spare: 20 amp fuse

B. Auxiliary: 15 amp fuse

C. PTO Clutch: 15 amp fuse

D. Main: 20 amp fuse

Check / Fill Transmission Oil Level

Oil Type: SAE 20W motor oil

1. Check the oil level when the unit is cold. The oil should be

up to the "FULL COLD" mark (A, Figure 23) on the

transmission oil reservoirs (B). If the oil is below this level,

proceed to step 2.

23

2. Before removing the reservoir cap (C), make sure that the

area around the reservoir cap and fill neck of the reservoir

is free of dust, dirt, and other debris. Remove the reservoir

caps.

3. Add oil up to the "FULL COLD" mark.

4. Re-install the reservoir cap.

Change Hydraulic Oil Filter

Change Interval: Every Hours (Initial hydraulic oil and filter

change after first hours of operation)

Filter Part Number: X2

24

NOTE: Removing the oil filter from the transmission will drain

the oil reservoir. Have a suitable container ready to catch any

spilled oil. The manufacturer recommends this be a dealer-only

service item.

1. Locate the hydraulic oil filter (A, Figure 24) on the side of

the transaxle.

24

2. Remove the filter cover (C) and o-ring (B).

3. Remove and discard the hydraulic filter.

4. Inspect all parts for wear or damage, replacing as

necessary.

5. Install the new filter, new o-ring and filter cover. Torque the

cover to ft. lbs. ( Nm).

NOTE: Use caution after changing the filter; air in the hydraulic

system may affect the responsiveness of the control levers.

Checking Tire Pressures

Tire pressure should be checked periodically, and maintained

at the levels shown in the Specifications chart. Note that these

pressures may differ slightly from the "Max Inflation" stamped

on the side-wall of the tires. The pressures shown provide proper

traction and extend tire life.

Lubrication

Lubricate the unit at the locations shown in Figures 25, 26, and

27 as well as the following lubrication points:

ferrisindustries.com

Sours: https://www.manualslib.com/manual//Ferris-Isz-Series.html?page=24

CHECK HYDRAULIC OIL LEVEL

1. Before removing the reservoir cap, make sure the

area around the reservoir cap and fill neck of the

reservoir is free of dust, dirt, or other debris.

2. Unscrew the reservoir cap (B, Figure 16).

3. Look down the filler neck of the hydraulic oil

reservoir (A, Figure 16) and observe the oil level.

When cold, the oil level should be approximately

4" (10 cm) below top of the filler neck.

4. If necessary, add either Mobil 1&#x;, 15W

synthetic oil or Castrol Syntec&#x; 5W oil. DO

NOT use conventional oils.

5. Reinstall the reservoir cap.

CHANGE HYDRAULIC OIL FILTER

Change Interval: Every Hours

Filter Part Number:

NOTE: Removing the oil filter from the filter base will

drain the oil reservoir. Have a suitable container

ready to catch any spilled oil. Ferris recommends this

be a dealer-only service item.

1. Locate the transmission oil filter (A, Figure 17).

2. Lubricate the new filter base with a few drops of

transmission oil. Fill the filter half full of oil.

3. Clean the area around the filter base and remove

the filter. Do NOT drain the hydraulic system oil.

4. Thread the new filter onto the filter base until the

gasket makes contact, then tighten 3/4 of a turn

more.

5. Run the unit for several minutes and check the

transmission oil level.

IMPORTANT NOTE: Use caution after changing the

filter; air in the hydraulic system may affect the

responsiveness of the control levers. Repeat step 5

until the air is out of the system.

Regular Maintenance

Figure Checking Hydraulic Oil Level

A. Hydraulic Oil Reservoir

B. Reservoir Cap

Figure Change Hydraulic Oil Filter

A. Hydraulic Oil Filter

Air Cooled Models

B

A

Liquid Cooled Models

B

A

A

29

Sours: https://www.manualslib.com/manual//Ferrishtml?page=31

Type oil ferris hydraulic

Many mower manufacturers will allow the use of 20W motor oil in their transmissions. While motor oil will work in many hydrostatic transmissions, there is a better option.

There’s no question that motor oil will capably work in mower hydrostatic transmissions. The mower will steer and it will be propelled forward and backward. But there are vital differences in the way that motor oil is formulated compared to dedicated hydrostatic transmission fluid. These differences can play a role in long term performance and component life.

The main factor to consider is that motor oil is designed for a completely different operating environment than hydrostatic transmission oil. Engine oils are formulated to deal with combustion and combustion by-products. There are very specific detergents and additives in motor oil that won’t affect performance or protection over the short term. But over time, these motor oil ingredients will limit the oil change interval and this can have an effect on long term component life.

The detergent ingredients in motor oil hold combustion by-products in suspension and prevent deposit formation. These ingredients are vital in an internal combustion engine. But not only are these ingredients not needed in a hydrostatic mower transmission, they can degrade and shear down over time. These degraded detergents can contribute to oil foaming, which can lead to compromised wear control.

AMSOIL 20W Synthetic Zero-Turn Hydrostatic Transmission FluidAnother advantage that a dedicated hydrostatic transmission oil has over motor oil is the ability to fight oxidation and corrosion. The hallmark of a good hydraulic fluid is oxidative stability and strong anti-corrosion chemistry. These attributes lead to longer service life and improved protection during storage.

Hydrostatic transmissions also have gears. The meshing of gears can shear down and thin out engines oils. Hydrostatic transmission oil is designed to withstand gear lubrication to a much greater extent than motor oil. This means that dedicated transmission oil has a superior ability to maintain its original viscosity and provide more reliable wear protection over the long term.

Conclusion

There’s no question that motor oil will work in mower hydrostatic transmissions that allow its use. But a dedicated hydrostatic transmission oil contains specific anti-foaming, anti-rust, anti-oxidation and anti-wear ingredients. This chemistry will allow for much longer service life, consistent performance and maximized transmission life. We recommend the new AMSOIL 20W Zero-Turn Synthetic Hydrostatic Transmission Fluid.

/by Marc RodenSours: https://www.oildepot.ca/motor-oil-specific-hydrostatic-transmission-fluid-zero-turn-mower/
Ferris Z3X Hydro Oil Change

What oil does a Ferris mower use?

Use high quality detergent oils such as "For Service SF, SG, SH, SJ" or higher. You can also use synthetic oils, which are acceptable at all temperatures.

Click to see full answer.


Moreover, which oil is best for lawn mowers?

For most mowers and weather conditions, your best bet is going to be SAE 30/SAE 10W oil. These oils are ideal for operation in warmer environments.

Furthermore, what kind of oil does a hyper tough lawn mower take? SAE 30

Hereof, what kind of hydraulic fluid does a zero turn mower use?

The fluid recommended for Hydro-Gear transmissions and pumps is a 20W motor oil or 15W synthetic motor oil.

Is synthetic oil good for lawn mowers?

When choosing lawn mower oil, use a high-quality detergent oil classified as "For Service SF, SG, SH, SJ" or higher. Do not use special additives. Synthetic oils are an acceptable oil at all temperatures. The use of synthetic oil does not alter required oil change intervals.

Sours: https://askinglot.com/what-oil-does-a-ferris-mower-use

Now discussing:

.

The fluid recommended for Hydro-Gear transmissions and pumps is a 20W motor oil or 15W synthetic motor oil.

If the machine has oil reservoirs, they are mounted to the frame behind the seat, for easy access and oil level check accessibility.

If the machine does not have reservoirs, but has independent transaxles, then they are considered to be maintenance free. As long as the machine is performing correctly, then Hydro-Gear recommends not to open up the transmission to check or add to oil level.

If you are seeing a performance issue or stronger whine to the transaxles, then definitely check the oil level first. Checking the fluid level on these transaxles can be a little more difficult.

Oil level can be measured at the vent hole/tube towards the back of the transaxle, on top. Sometimes this hole can be accessed from above the frame, but if not, the transaxles may need to be removed (or just dropped down) and set on a level surface.

Clean the area around the tube and take care so no dirt or debris falls into the hole, before taking the tube and grommet off.

Note: The more this vent is opened the more likely dirt will fall in and damage the transaxle.

Use some type of dipstick, such as a metal rod/wire and measure down from the top of the case. The level should be at 1" to " from the top of the case. Add the recommended engine oil as needed and Do Not overfill the transaxle.

If you are still unsure please contact your Ariens dealer, if you do not know who this is please see the link below:

Ariens Dealer Locate

Sours: https://support.ariensco.online/support/solutions/articles/what-is-the-suggested-hydrostatic-fluid-to-use-on-my-zero-turn-machine-how-is-the-oil-level-checked-


1158 1159 1160 1161 1162