Wrf736sdam13 diagnostic mode

Wrf736sdam13 diagnostic mode DEFAULT

Ice maker stopped making ice.

Cause 1

Freezer Temperature is Above 10 Degrees F (-12C)

If the freezer temperature is above 10 degrees Fahrenheit (-12C), the ice maker will not produce ice cubes efficiently. The freezer temperature should be set between 0 and 5 degrees Fahrenheit (-18 to -15C) for the ice maker to work properly. If the freezer temperature is too high, ensure that the condenser coils are clear of debris and the condenser fan is working properly. In addition, check to see if frost has accumulated on the evaporator coils. If the evaporator coils are frosted over, part of the defrost system has likely failed.

Cause 2

Water Inlet Valve

The water inlet valve is an electrically-controlled valve that opens to supply water to the dispenser and ice maker. If the water inlet valve is defective, or if it has insufficient pressure, it won’t allow water to flow through. As a result, the ice maker won’t make ice. The valve requires at least 20 psi to function properly. Make sure that the water pressure to the valve is at least 20 psi. If the water pressure is sufficient, use a multimeter to check for power to the water inlet valve. If the water inlet valve has sufficient pressure and is getting power, but the ice maker won’t fill with water to make ice, replace the water inlet valve.

Cause 3

Ice Maker Assembly

One component of the ice maker assembly might be defective. Since many of the ice maker components are not sold separately, you may need to purchase and replace the entire ice maker assembly. Before replacing the ice maker assembly, check the water inlet valve, water line, and fan. If none of these parts are at fault, and the freezer temperature is at least 15 degrees Fahrenheit, replace the ice maker assembly.

UPDATE 3/2/19 For those that have less common problems here’s the complete list

Cause 4

Icemaker Module

The icemaker module is equipped with a motor that cycles the ice ejector arms or turns a tray to eject the cubes into the ice bucket. When the thermostat or sensor on the icemaker tray reaches about 15 degrees Fahrenheit, the motor cycles to release the ice cubes. At the end of the cycle, the icemaker module sends power to the water inlet valve to refill the tray with water. If the icemaker module is defective, the ice maker won’t make or dispense ice. First, depending on your model, make sure that the on/off switch is in the on position or the bail arm is in the down position. If the icemaker module has ejector blades, check to ensure that ice cubes are not stuck in the blades. There are usually test points in the module that a technician can use to further diagnose problems with the module.

Cause 5

Low Water Pressure from House Supply

The home may have insufficient water pressure. The water inlet valve supplies water to the ice and water dispenser. The water inlet valve requires a minimum of 20 psi to function properly. Check the water flow and test the pressure to determine if it is at least 20 psi.

Cause 6

Door Switch

The door switch turns off the ice and water dispenser when the refrigerator door is open. If the door switch fails, the dispenser will not turn on. To determine if the door switch is defective, use a multimeter to test it for continuity. If the door switch does not have continuity when activated, replace it.

Cause 7

Ice Level Control Board

Some refrigerators use an infrared beam to sense the level of ice in the ice bucket. When the ice level reaches the top of the bucket, it interrupts the infrared beam. The control board then shuts off the ice maker. When the ice level drops below the beam, the control board signals the ice maker to make more ice. If the ice level control board fails, the ice maker will stop making ice. Ensure that the ice level control board is getting power. If the ice level control board is getting power, but the ice maker won’t work, replace the ice level control board.

Cause 8

Water Filter

A clogged water filter can restrict the flow of water to the dispenser and prevent the ice maker from working properly. The water filter should be replaced about every six months to maintain proper water flow and ensure water quality.

Cause 9

Icemaker Mold Thermostat

The icemaker mold thermostat monitors the temperature of the ice mold (ice tray). Once the mold reaches the proper temperature, the icemaker ejects the ice cubes and refills the ice mold with water. If the mold thermostat is defective, the ice maker will stop making ice. To determine if the thermostat is defective, use a multimeter to test it for continuity. If the mold thermostat does not have continuity, replace it. (Note: If the ice maker is not cold enough, the mold thermostat contacts will open. If the thermostat contacts are open, the ice maker will not make ice. The ice maker temperature must generally be lower than 20 degrees Fahrenheit for the thermostat contacts to close.)

Cause 10

Icemaker Switch

The ice maker switch might be defective. It is also possible that the icemaker switch got turned off by accident. Check the switch to ensure that it is turned on. If the icemaker switch is turned on, but the ice maker still isn’t working, use a multimeter to test the switch for continuity. If the icemaker switch does not have continuity, replace it.

You can find a few more things to try on the Frigidaire ice maker not working guide—even though it’s for Frigidaires, a lot of the same solutions apply.

Was this answer helpful?

YesNo

Voted Undo

Score12

Cancel

Sours: https://www.ifixit.com/Answers/View/407671/Ice+maker+stopped+making+ice.

FREEZER UPRIGHT KENMORE 25328262804 "Customer complaint that unit is not cooling properly, temperature at 44 degrees, partial frost pattern on evaporator, system has a leak, unit needs new evaporator and filter drier, customer does not want repair ; ordrng 1 297414800 (Evaporator) and 1 WP

OTR MICROWAVE MAYTAG MMV1174FZ0 I disassemble the microwave I was about to install the parts and realize there was no capacitor. Capacitor never got delivered customer also does not have the packing slip. Capacitor inside the microwave is burnt capacitor needs to be ordered; ordrng 1 W1

WASHER MAYTAG MHW6630HW CC that F3e2 code comes on. They had a different company come out and they replaced the control. Found the wire to the control in the wrong spot. Reconnected the wires. Started a cycle. Optest ok.

COOKTOP GAS GE JGP945SEK2Ss Replaced the harness. Optest ok; used 1 SHIPPING (shipping and handling) from stock

RANGE WHIRLPOOL WFG320M0BS3 CC that the oven does not heat. Checked the igniter 0 amps. Will need an igniter. Replaced the igniter from t/s. Optest ng. Control sending 0 volts to the igniter. Cust had a main control. Replaced the control. Heated oven to 350*. Optest ok.; used 1 1240

WALL OVEN KITCHENAID KOSE500ESS04 CC that the the lights are flickering. He has replaced the bulbs multiple times. Advised cust the volts is dropping below 210 volts then coming back to 240* or in between. Advised cust Will an electrician. Optest ok.

RANGE KENMORE 665.5844003 "CC that the temperature control does not adjust up or down. Found the key pad not responding. Will need a new membrane. ; ordrng 1 WP8272646 (Membrane), used 1 SHIPPING (shipping and handling) from stock"

Near University Heights, OH 44118

REFRIGERATOR WHIRLPOOL WRS571CIHZ01 "CC that the food is freezing food. Checked thermistors, passed. Top shelf is overpacked with food. Called t/l. Advised cust to not overpack the ff section and raised the ff to 39* and Fz 2*. Optest ok"

Near North Ridgeville, OH 44039

REFRIGERATOR WHIRLPOOL WRF535SMBM00 Replace all parts opt test ok

REFRIGERATOR WHIRLPOOL GX5FHTXVY04 Installed fill tube and clip. Cycled ice maker. Op test ok

Near Harpersfield Township, OH 44041

DBL WALL OVEN KENMORE 790.4200361 "I install the new part unit did not test good but the main control board does have visual issues I can hear the control board for the fans in the rear cutting in and out customer wants to continue with the repair to replace the board in the back; ordrng

Near Mentor-on-the-Lake, OH 44060

REFRIGERATOR KITCHENAID KRMF706ESS01 "Cc unit ice maker stopped working, now unit not cooling.Unit running when I arrived, temps in ff section at 50, freezer at 15. Ran ice maker diagnostics, unit is not displaying any ice maker information. Also noticed, 3way valve in rear of unit is consta

Near Madison Township, OH 44057

FREEZER FRIGIDAIRE FFC0923DW1 Cc: not coolingFound compressor is running and humming. Unit pulling .6 amps. See no damage from movers that could have caused system to stop cooling. Needs compressor and drier.Customer does not want to repair at this time

REFRIGERATOR WHIRLPOOL WRF535SWHV02 "Customer complaint that liner is cracked, confirmed, used liner repair kit to repair, op test good"

Near North Ridgeville, OH 44039

WASHER MAYTAG MHW5630HW0 "Cc that the unit doesnt do anything. Once you start a cycle control will click but nothing happens. Confirmed issue. Ran diag found error code F0E5 Off balance load and F0E2 Over suds. Replaced main control. Started a normal cycle , good. Explain cust to

REFRIGERATOR KITCHENAID KBFN502EPA02 Cc lights out Found upper ff lights outNeeds leds ; ordrng 2 W11462342 (Silver led)s

Near Painesville, OH 44077

DRYER HOTPOINT HTDX100EM8WW "Cc unit settings not workingCustomer stated all settings work, but the wrinkle free setting, it was too hot and her clothes were wrinkled. Checked timer operation. Found white wire to timer connection had come off, terminal tension too loose. Tightened s

FREEZER WHIRLPOOL WZF79R20DW03 "Cc unit door not sealingCustomer stated there was a gap in the door gasket when they first received it. It seems to have almost sealed up now. Confirmed only a small gap remaining on upper left corner of gasket, the rest of the gasket Is sealing good. Hi

DISHWASHER WHIRLPOOL WDF520PADM7 "Cc that the unit is not drying the dishes. Ran diag, no error codes. Ran auto test. Advice cust to run hot water before starting unit and to use rinse aid , this will help to dry dishes bette."

Near Newbury Township, OH 44065

REFRIGERATOR WHIRLPOOL WRX735SDBM00 Cc light not worked Found all leds functioning properly

Near University Heights, OH 44118

WASHER WHIRLPOOL WFW92HEFU0 "Customer complaint of water collecting in bellow, found drain holes plugged, cleared, unit is operating as designed"

Near North Olmsted, OH 44070

RANGE WHIRLPOOL JGR8850BDQ "Replace sensor probe preheated oven ,opt test ok"

DISHWASHER GE GDT580SMF6ES Installed drain hose. Ran test cycle. Op test ok

DRYER MAYTAG MED7230HW0 "Cc unit not drying clothes fullyRan diagnostics, no codes stored. Ran dryer op test on timed, checked heat and airflow. Good heat at exhaust, reading average 157 degrees. Airflow at vent outlet slightly low, customer stated he cleaned venting already. Ve

WASHER MAYTAG MVWC565FW2 "Customer complaint that unit is not starting, started normal wash cycle, lights lit up, unit began filling, unit filled and began washing, canceled cycle and repeated several times with same results, ran diagnostics found f1e2(motor control fault) an

WASHER AMANA NTW4516FW2 Customer daughter was there she couldn’t find pop advise her to get it asp other wise she will get bill ran diagnostics found no fill long fill code and shifter fault delete all error code also found hot water valve off advise customer to leave it on but

DRYER WHIRLPOOL WED6620HC1 "Replace element,opt test ok"

DISHWASHER MAYTAG MDB7749AWB2 Found a bad latch it had broken pieces and panel screw plastic hole all broken gave her estimate she will not fix shes getting new

Near North Ridgeville, OH 44039

DRYER AMANA NED4655EW1 "Cc that the unit takes 2 hours to dry a pair of jeans. Power is good. Started unit, unit is heating and cycling. Couldnt check vent because is vented to the roof. Advice cust to clean vent going outside, its never been clean so its probably clog and it w

DISHWASHER GE GDT680SSH6SS "CC that the unit does not drain every time. Found the drain pump vibrating. Removed the drain hose felt the propeller loose. Will need a new drain pump.Cust is going to install. ; ordrng 1 WD19X25187 (Drain pump), used 1 SHIPPING (shipping and handling)

Near Strongsville, OH 44149

DISHWASHER WHIRLPOOL WDT970SAHZ0 "Cc middle rack and 3rd rack squeaking. Let customer know the rubbing is most likely caused by water/detergent getting on parts and drying them out. Lubed up all surfaces. Tested, had customer test. Good. Op test ok"

DRYER SAMSUNG DV42H5000EWIA3 Installed new part did not work needs a control board customer wants a reimbursement. We are not continuing with the repair; used 1 SHIPPING (shipping and handling) from stock

Near Strongsville, OH 44136

DRYER MAYTAG MEDC465HW "Tested unit out. Let run for 20 mins, timer is moving, good. Tested different temp cycles, signal is working. Op test ok"

Near Bedford Heights, OH 44146

DRYER MAYTAG MEDX655DW1 Customer showed pop took pic Cc unit not turning on Found black power lead burnt Replaced terminal using truck stock I do not have correct power cord to run full test Customer to replace cord ; used 1 279320 (BLOCK-TERM) from stock

Near Painesville, OH 44077

OTR MICROWAVE WHIRLPOOL WMH53521HZ4 Installed the new part op tested good.

WASHER MAYTAG MVWB835DW4 There was a flood in their basement between last time I was here and now I took pictures of the damage it needs everything now. I have the gear case for return just in case the warranty denies it. As the warranty will proceed with the repair your case wil

RANGE WHIRLPOOL WFG505M0BS3 "Replace door,opt test ok"

Near Warrensville Heights, OH 44128

RANGE WHIRLPOOL WFG320M0BB2 "Frame on door glass broken off again and bent( see pics), reordering ; ordrng 1 Wpw10535776 (Door glass)"

Near Andover Township, OH 44003

WASHER FRIGIDAIRE FFFW5000QW0 I ran a cycle is filled with water and agitated for about 10 minutes the unit did not leak a drain and spun machine unit tested good

Near Strongsville, OH 44136

WASHER WHIRLPOOL WTW4955HW1 "Cc unit vibration, noise. Went over noises with customer, the valves opening and closing, unit switching between agitate and spinning, drain pump activating. Ran diagnostics, no error codes, ran diagnostics cycle. Good. Ran calibration, good. Threw towel

Near North Madison, OH 44057

REFRIGERATOR WHIRLPOOL WRF560SEHZ00 The fill tube for the icemaker was frozen I steamed out the fill tube in the unit tested good

Near Broadview Heights, OH 44147

WASHER MAYTAG MVWB725BW0 Replaced all parts. Tested. Good. Op test ok

WASHER WHIRLPOOL WTW5105HW0 "Customer had and off balance load but she been running it and it been good check shocks confirm good basket did not bounce more than once,also delete code and ran calibration and auto test pass advise customer to only load unit 6-7 regular bath towels an

Near Concord Township, OH 44077

REFRIGERATOR FRIGIDAIRE FGHD2368TF3 "Cc: not making ice, not fillingCycled ice maker. Found ice maker is cycling and calling for water. Fill tube frozen. Needs water valve and fill tube; ordrng 1 241920106 (FILL TUBE2858) and 1 242253002 (valve-water11372), used 1 SHIPPING (shipping and han

WASHER MAYTAG MVWB765FW "Cc unit codes LF, will not cycleRan diagnostics, found codes f8e1 for no fill/low flow. Ran manual valve test, hot water valve humming, no water coming in. Checked water pressure at wall valve, no water. Found closed water valve at hot water tank connect

Near Broadview Heights, OH 44147

DISHWASHER KITCHENAID KDPM704KPS0 Cc that the unit is leaking on left corner. Took pics of how unit is leaning before and after I adjusted it. Replaced all parts and watch unit for 20 min. No leaks. Op test ok

DRYER WHIRLPOOL MEDC465HW0 "Cc unit not heating/dryingCustomer showed popRan dryer op test, airflow just barely warm when set to high. Checked power in to unit, good at 233v. Found power plug miswired to unit, L1 and N switched on terminal block, element only receiving 120v. Correc

Near North Royalton, OH 44133

DRYER WHIRLPOOL WGD8000DW4 "Cc that the unit started on its own. Try to get unit on diag no good. Replaced UI, old UI had moisture on control, took pics. I was able to put unit on diag with new UI found no error codes, ran unit , is heating . Op test ok no core."

COOKTOP GAS JENN-AIR CVG4280W "Customer complaint that left side igniters on cooktop are not working, confirmed, found igniter physically broken, unit needs new igniter ; ordrng 1 WP71002179 (Igniter)"

DRYER WHIRLPOOL WGD75HEFW0 "Cc that the unit vibrates a lot and its noisy. Confirmed. Found blower wheel full of lint. Cleaned all out, op test ok. Told cust that the more detergent and the more softener that they put on their washer the more lint theyll see on dryer. 1 to 2 tables

WASHER WHIRLPOOL WFW9250WW01 "Cc unit giving error Ran diagnostics found error for drain pump Inspected drain pump Pump seems weak Also found bearings to loud Advised customer on issues ; ordrng 1 WPW10730972 (pump-water) and 1 WP285655 (clamp), used 1 SHIPPING (shipping and handling

WALL OVEN WHIRLPOOL WOD93EC0AS01 Installed fuse Ran test bake OP Test Ok ; used 1 SHIPPING (shipping and handling) from stock

Near Garrettsville, OH 44231

REFRIGERATOR WHIRLPOOL GS5SHAXNL00 Installed fan motor and blade OP Test Ok ; used 1 SHIPPING (shipping and handling) from stock

RANGE WHIRLPOOL WFG525S0HS0 "Cc unit not baking Found control board not sending power Needs control board ; ordrng 1 W11317846 (Control), used 1 SHIPPING (shipping and handling) from stock"

Near Streetsboro, OH 44241

WASHER WHIRLPOOL CAE2745FQ1 Installed drain pump OP Test Ok

Near North Madison, OH 44057

REFRIGERATOR WHIRLPOOL MSC21C6MFZ00 Customer has installed a new filter when I recommended for him to install a new filter the water pressure is still low needs a new filter head assembly; ordrng 1 WPW10394053 (housing)

Near WILOUGHBY HLS, OH 44094

RANGE FRIGIDAIRE LFGF3054TFB Installed harness. Tested. Op test ok

Near South Euclid, OH 44121

DRYER WHIRLPOOL WGD7120HC0 "Cc unit not operating.Found unit will not power on or respond. Unplugged unit, plugged back in. Unit powering on normally. Started dryer cycle, good heat, op test good. Unit is plugged into a GFCi outlet, advised customer not recommended to use this outl

WALL OVEN WHIRLPOOL WOD51EC0HS01 Replaced Glass door. Op test ok.

Near South Russell, OH 44022

REFRIGERATOR WHIRLPOOL KRFC300ESS "Cc of no water Suspect of bladder frozen Removed bladder no ice Found filter head to be malfunctioning Needs filter head ; ordrng 1 W11346623 (Filter head), used 1 WR2X8545 (1/4 UNION), and 1 SHIPPING (shipping and handling) from stock"

Near South Euclid, OH 44121

REFRIGERATOR WHIRLPOOL WRX735SDHZ02 "Cc unit not making iceFound ice in ice mold, jumped t to h, ice maker could not index, ice jammed in ice mold. Cleared ice from ice maker. Reran harvest test, ice maker indexed properly, filled mold with water. Op test good."

Near Broadview Heights, OH 44147

RANGE WHIRLPOOL WFE714HLAS0 Replaced part. Tested bake at 350*. Cycled and heated. Op test ok

Near Valley View, OH 44125

WALL OVEN WHIRLPOOL WOD77EC0HS01 "Installed new controls and user interface , op test good"

Near Munson Township, OH 44024

DRYER GE GHDN520ED0WS Cc unit making grinding noise Found rear bearing to be worn as well as front sliders Needs bearing and sliders ; ordrng 1 WE25M40 (bearings) and 2 WE1M504 (slide drum (wht))s and 2 WE1M1067 (slide bearing)s

RANGE WHIRLPOOL WFE525S0JZ "Found l2 black wire burn and broken replace parts from t/s and replace control,opt test ok ; used 1 W11416047 (TERM BLOCK KIT - RANGE) from stock"

Near Williamsfield, OH 44093

RANGE WHIRLPOOL WFG550S0HZ0 Cc of error f3e0 Found Thermostat open when unit reaches 150 in temp Used back stock thermostat to test unit will reach 195-200 and will not go pastNeeds thermostat and temp sensor Spoke to BJ he said parts should still be covered ; ordrng 1 W10833885 (se

Near East Cleveland, OH 44112

REFRIGERATOR WHIRLPOOL WRS315SDHM01 Installed water valve. Tested water dispenser and cycled ice maker. Op test ok

DISHWASHER MAYTAG MDBH989AWB1 Cc: not drying all waterRan test cycle. Found unit is draining all the water out. See no signs of water valve seeping. Found customer does not have drain loop installed under sink. Advised customer of back filling from sink. Ran another test cycle. Op tes

RANGE WHIRLPOOL WFE505W0JZ0 "Customer complaint that unit smelled like burning electrical when front burners were on, found terminal block burning, installed new terminal block and harness, op test good ; used 1 W11416047 (TERM BLOCK KIT - RANGE) from stock"

WASHER WHIRLPOOL WTW4816FW2 "Replace control and actuator,ran diagnostics opt test ok"

Near Eaton Township, OH 44044

ICE MAKER KITCHENAID KUIX305ESS2 "Replace thermister,opt test ok"

WASHER WHIRLPOOL WTW5000DW3 "Took pop. Cc that the unit is not filling with enough water. Ran diag no error codes. Ran auto test, good. Started a normal cycle , good. Explain cust how much water the unit puts in washer and 6 to 7 bath towels = a full load, 1 to 2 tablespoons of de

REFRIGERATOR WHIRLPOOL WRF560SMHZ00 CC that the ice maker is not working. Found ice build up on the stripper cleared the ice. Ice maker cycled. Advised cust to replace the saddle valve with an inline valve. Will need a plumber. Optest ok.

Near Geneva Township, OH 44041

DRYER WHIRLPOOL WED72HEDW1 "Cc: not heatingFound unit receiving proper power. Found element open. Needs element.Element shows out of stock, office to reschedule; ordrng 1 WP8544771 (element10349), used 1 SHIPPING (shipping and handling) from stock"

Near Highland Heights, OH 44143

DISHWASHER JENN-AIR JDB8200AWS3 Installed drain pump. Ran test cycle. Op test ok

Near Highland Heights, OH 44143

DISHWASHER KITCHENAID KDPE234GPS0 Installed dispenser. Ran test cycle. Op test ok

Near Highland Heights, OH 44143

WASHER MAYTAG MVWB835DW4 Cc: off balanceCustomer states it was bulky items. Customer stated the items were balled up. Found error codes f0e5(off balance) f2e1(stuck key). Ran auto test. Ran high speed spin. Basket well balanced. Tested suspension. Advised customer on loading. Adv

FREEZER WHIRLPOOL WRB322DMBM01 "Installed new air damper, op test good"

DRYER MAYTAG 110.858624 Cc: squealing noiseFound rollers worn. Needs dryer repair kit. Installed dryer repair kit. Ran test cycle. Op test ok; used 1 4392067 (DRYER REPAIR KIT4783) from stock

Near WARRENSVL HTS, OH 44122

DISHWASHER KITCHENAID KDFE104HPS1 "Cc: not filling, not washingFound unit is filling. Sump receiving proper power(115v). Needs sump assembly. Replaced sump assembly. Ran test cycle. Unit still not washing. Ohmed out sump from control. Sump checks good. Needs control. Control shows out of

DRYER KENMORE 110.728321 "Cc: drum not turningFound belt snapped, needs dryer repair kit. Installed dryer repair kit. Ran test cycle. Op test ok ; used 1 4392065 (DRYER REPAIR KIT4830) from stock"

Near Maple Heights, OH 44137

WASHER MAYTAG MVW6230HW0 "Cc unit not starting a cycle.Found unit dial selector will not work, display is “please rotate knob to available cycle”. Checked console connectors, found ribbon connector to rotary knob halfway disconnected. Properly connected and retaped to prevent con

REFRIGERATOR MAYTAG MFW2055FRZ00 "Cc: not cooling properlyFound freezer temps at 41 degrees, ff temps at 72 degrees. Found evap fan not running, found ball of ice on cap tube. Entered diagnostics, watched frost pattern and amp draw. Unit pulling 1.1 amps and building frost pattern. Evap

REFRIGERATOR WHIRLPOOL WSR57R18DM02 "Customer complaint that unit is making noise, raise unit up off rollers, noise stopped"

REFRIGERATOR FRIGIDAIRE FRS6HR45KSO "Installed new ice maker , op test good"

RANGE WHIRLPOOL WFG320M0BS3 "Customer complaint that oven light is not working, bulb is blown, installed new bulb , op test good ; used 1 8009 (APPLIANCE BULB) from stock"

Near Valley View, OH 44125

WASHER WHIRLPOOL MVWB765FW4 "Cc unit lid broken on both sidesConfirmed,broken lid. Replaced unit lid using customer supplied pre Id part. Lid function normal. Op test good."

WASHER AMANA NTW4516FW3 "Installed new lid lock, op test good"

DBL WALL OVEN JENN-AIR JJW2830WW00 "Installed new control, op test no good , have 14vdc to user interface, user interface is just flickering now, needs new user interface, customer said they do not want us to order user interface and replace it; ordrng 1 W10401272 (Ui)"

REFRIGERATOR WHIRLPOOL WRS311SDHM02 "Customer complaint that fresh food section is not cooling, fresh food section temperature at 71 degrees, freezer section temperature at 10 degrees, air damper is closed, unit needs new air damper control ; ordrng 1 W11380595 (Air damper)"

Near Seven Hills, OH 44131

MICROWAVE FRIGIDAIRE FGMV175QFA CC that the unit does not trip. Found the door switch open. Replaced the door switch from t/s. Optest ok; used 1 W10269458 (Microswitch) from stock

GARBAGE DISPOSAL WHIRLPOOL KBDS100T3 "Installed new garbage disposal, op test good"

Near Broadview Heights, OH 44147

RANGE WHIRLPOOL WFE301LVQ0 "CC that the oven will heat but after 45 minutes is quits working. Turned oven on, let run for for 30 minutes cycling every time. Ran diag no codes. Temp sensor is good. Will need a main control. Cust is going to call warranty company to see if they can g

Near Columbia Township, OH 44028

WASHER MAYTAG MVWB835DW5 Replaced parts. Tested. Good. Ran test 51/52. Good. Op test ok

Near Broadview Heights, OH 44147

REFRIGERATOR WHIRLPOOL WRF767SDHZ00 CC that the ff section is not cooling. Ff 60 Fz 3. Found the evap fan not running 0 v from control. Will need a control and evap fan.; ordrng 1 W11224591 (Evap fan) and 1 W11224256 (Main control)

Near North Royalton, OH 44133

WASHER WHIRLPOOL WTW5100HC0 Replaced the belt. Started a spin cycle. Optest ok.

Near North Royalton, OH 44133

SXS REFRIGERATOR WHIRLPOOL WRS315SNHM03 "Recovered refrigerant, replaced compressor and drier, pulled 28vac w/ pump, watched, good, charged 5.5 r134a, unit cooling, pressures good, op test ok"

Near Brook Park, OH 44142

WASHER MAYTAG MVWC465HW2 "CC that the unit does not finish a cycle, clothes are wet. Ran diag no codes. Ran a bulky cycle with towels and a rinse and spin. Optest ok."

Near Strongsville, OH 44136

DISHWASHER WHIRLPOOL WDT730PAHZ0 Replaced panel. Tested. Good. Op test ok

Near North Royalton, OH 44133

REFRIGERATOR WHIRLPOOL WRT311FZDW00 "Cc unit not cooling. Compressor is loud, and found ball of ice on evap line. Ordering comp and evap, dye filters. *** requesting double labor *** 4 job count; ordrng 1 W10836706 (evaporator) and 2 WPW10143759 (dryer)s and 1 WPW10507886 (compressor)"

Sours: https://fredsappliance.com/service-history-144/
  1. Orange outdoor flower pots
  2. Food and staples retailing
  3. A 1 stump removal
  4. 4x6 bathroom layout

Whirlpool Refrigerator Repair -Control Board Diagnostics-

This refrigerator troubleshooting and repair guide will show you how to access your refrigerator's diagnostic mode to test every part of the refrigerator from temperature sensors and evaporator fan motor to the refrigerator's compressor and defrost system. If you detect a problem with one of these refrigerator parts try looking at the refrigerator troubleshooting page for more repair help focused on that refrigerator part.

Starting Diagnostics

To start with we need to start the refrigerator's diagnostic mode. To do this open the refrigerator door and press one or both door switches, depending on your refrigerator type. Next press the refrigerator temperature (+) button three times in ten seconds and release the light switch or switches. This should display an "S" in the freezer display and an "E" in the refrigerator display. Then press the refrigerator temperature (+) button one time to confirm that you want the service mode. You will then see a set of numbers displayed showing the software version for three seconds. (Again this control board is used on many different refrigerators.) After the software version is shown the freezer display should show "1" and the refrigerator display should be blank. Congratulations! Pat yourself on the back, you are now ready to do refrigerator diagnostic magic! Within the refrigerator diagnostic test mode there are 6 diagnostic tests:

  1. Defrost Thermostat Diagnostics
  2. Refrigerator Compressor & Condenser Fan Diagnostics
  3. Freezer Evaporator Fan Diagnostics
  4. Refrigerator Sensor Diagnostics
  5. Freezer Sensor Diagnostics
  6. Refrigerator Damper Door Diagnostics

You can select the test number you would like to run by pressing the freezer temperature (+) or(-) button until the test number you want is in the freezer display. Then using the refrigerator(+) button to cycle the test on and off.

NOTE: Most tests will need to be turned off before you will be allowed to move to the next test with the freezer temperature buttons.

Test#1 Defrost Thermostat Diagnostics

After pressing the refrigerator (+) button you will see ether an "O" or an "S". "O" means that the freezer's defrost thermostat is open and will not allow electricity to reach the defrost heater. An "S" means shorted or closed. The word shorted sounds bad but actually that is what you want to see if the freezer is cold. If you see an "O" (open) and the defrost thermostat is cold that means you need to replace the thermostat. The thermostat should be shorted or closed anytime it is cold and it's safe to run a defrost cycle. This test will also check the defrost heater. If ether the defrost thermostat or heater are broken or "open" and the evaporator is iced up, you will need to replace the bad part. For more information on refrigerator's defrost system take a look at this video. (Refrigerator Defrost Troubleshooting Video)

Back to Top

More

Sours: https://applianceassistant.com/Refrigerator-Repair/W10503278-Refrigerator-Control-Diagnostics-Repair.php

We serviced a

KITCHENAID REFRIGERATOR

Model KSSC42QMS01

Near Austin, TX 78732

"Arrived on site for no ice . Ran harvest on IM didnt harvest or activate valve . Found Teflon coating flaking off . And cracks . Also found optics failing as well. Ordering ice maker and optics control, AUTHO. No water leaks detected at time of service. Call to set return ; ordrng 1 W10757851 (Optics) and 1 AUTHO"

We serviced a

WHIRLPOOL DISHWASHER

Model WDF540PADM3

Near Leander, TX 78641

Arrived onsite for dishwasher not washing and no water entering the unit. Upon inspection I found no error codes stored in the system. I ran diagnostics and found the valve vibrating but no water. I found the water valve for the under the sink was turned off. I turned the water on and tested again. The unit is now working as designed with no leaks detected during time of service. Job complete.

We serviced a

WHIRLPOOL DISHWASHER

Model WDT750SAKZ0

Near Georgetown, TX 78628

Arrived onsite for previously diagnosed parts. Removed and replaced heater. And proceeded to test unit found no leaks during service. Job Completed.

We serviced a

KITCHENAID OVEN

Model KODT100ESS04

Near Austin, TX 78735

"Arrived onsite to install previous diagnosed TOD, installed TOD, tested top and bottom to 350 degrees,unit now working as designed,job complete"

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706ESS04

Near West Lake Hills, TX 78746

We serviced a

WHIRLPOOL WASHER

Model LAT8504AAE

Near Austin, TX 78731

Arrived onsite for washer not responding after fill. Upon inspection found failed lid switch assembly. Jumped switch and unit began to drain and spin. Office to reschedule.; ordrng 1 WP22001682 (switch-lid)

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHZ05

Near Austin, TX 78723

"Arrived on site for fridge still tripping breaker . Ran defrost heated test in diagnostic . Ohmed heated , checked normal. Checked voltage to heater ,breaker tripped . Ordering evap harness. No water leaks detected at time of service. Call to set return ; ordrng 1 W11545823 (Evap harness)"

We serviced a

KENMORE REFRIGERATOR

Model 106.535692

Near Austin, TX 78759

"Arrived on site for not making ice . Found both icemaker ( cracked and leaking ) and burn maker on optics control. Replaced both parts and ran harvest. All checked normal.No water leaks detected at time of service. Job complete."

We serviced a

MAYTAG WASHER

Model MHW5500FW0

Near Austin, TX 78750

Arrived on site to diagnose washer that is throwing F9E1 error for slow drain. Found unit is draining ultra slow. Unit full of dog hair. Removed drain trap and removed dog hair and debris. Reassembled and verified unit draining as designed.

We serviced a

WHIRLPOOL DISHWASHER

Model WDF330PAHS5

Near Pflugerville, TX 78660

Arrived onsite for dishwasher upper wheel having broken on right front. Replaced and tested unit is now operating as designed. Job Completed.

We serviced a

WHIRLPOOL DISHWASHER

Model WDT750SAKZ0

Near Cedar Park, TX 78613

Arrived on site to install previous diagnose part. Inspected work area and unit. Found unit already pulled out of it hole. We found heating element bushings torn. We uninstalled it and installed new updated element. We rant the unit though a diagnostics cycle and check for leaks found no leaks at this time unit working as designed. Customer wanted us to unit where it was. Job complete

We serviced a

KITCHENAID DISHWASHER

Model KDTE104KPS0

Near Austin, TX 78745

"Arrived on site to test unit for no drain, tested unit found loose connection on drain pump, secured connection, tested unit, unit now draining properly, no leaks detected job complete"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX988SIBM03

Near Pflugerville, TX 78660

Arrived onsite for fresh food evap ice build up on one side that had not been present since the clogged drain. Exposed evap and Cleared all ice. All checks good. Unit is now operating properly.

We serviced a

WHIRLPOOL OVEN

Model WOS51EC0HS02

Near Meadowlakes, TX 78654

"Arrived on site for a wall oven with the light not turning off. Upon arrival the door was closed and the light was on, even when it should of been off. Upon further inspection I found the door making good contact with the latch. I removed the door and manually tested the latch. I found it intermittently not clicking and the switch not working. I gained access to the latch and found all connections and the contact on the latch arm to switch good. This indicates a faulty latch needing to be replaced. I powered the unit down at the breaker and then installed a new latch. I tested the new latch and found it working as designed. Call complete."

We serviced a

KITCHENAID REFRIGERATOR

Model KFXS25RYMS4

Near Buda, TX 78610

"Arrived On site and Inspected Refrigerator and found both interior sections are room temperature. Another service company has already replaced start device. Refrigerator has been running for one hour and compressor is 160?, Compressor is seized and will need to be replaced. . ; ordrng 1 WPW10466675 (Compressor) and 1 WPW10313899 (Evaporator) and 1 W10143759 (Dye drier) and 1 Wpsav4 (Stub) and 1 876765 (Tube kit)"

We serviced a

WHIRLPOOL WASHER

Model WFW72HEDW

Near Kyle, TX 78640

"Arrived on site and found washer is unplugged, after reconnecting the power door lock is clicking repeatedly and washer is showing F5E3. Replaced door lock and ran a diagnostic cycle and it completed properly, job complete."

We serviced a

WHIRLPOOL RANGE

Model WFE535S0JS0

Near Manor, TX 78653

Arrived onsite for range odor. Upon arrival tested unit. Found that ?odor? customer was experiencing was from oils burning off from elements applied in manufacturing. Ran unit bake at 450 degrees and broil at 500 degrees to assist in burning off residual oils. Unit is functioning as designed. Job complete

We serviced a

KITCHENAID DISHWASHER

Model KDTM404ESS3

Near Austin, TX 78746

"Arrived onsite to test unit for bent element,tested unit found element warped, replaced element, tested unit,unit now working as designed, no leaks detected job complete"

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706ESS01

Near Austin, TX 78737

"Arrived onsite for unit making noise. Heard the unit making noise when walking in. Heard the noise, looked at the pantry UI and saw it wasn?t working. Looked under the pantry UI and saw that it had a bunch of water under the UI panel damaging the panel and the wires underneath. No other issues at this time. Job complete

We serviced a

KENMORE DISHWASHER

Model 665.13443K900

Near Dripping Springs, TX 78620

"Arrived on site for customer complaint of unit not draining, found clog in drain hose, I cleared drain hose, unit tested good, also found someone added mounting screws into side of tub which may cause unit to leak."

We serviced a

KITCHENAID DISHWASHER

Model KDFM404KPS0

Near Austin, TX 78729

Arrived on site to install previously diagnosed parts. I installed the new drain pump and vent motor. I then ran a test cycle in diagnostics and found the unit working as designed. No leaks observed at the time of service. Call complete.

We serviced a

WHIRLPOOL OVEN

Model WOD51EC0HS02

Near Belton, TX 76513

"Arrived on site for wall oven not turning fan off. Power to unit was cut off on arrival. Upon arrival I found no errors in diagnostics but did find when power had been applied fan wouldnt turn off and unit was room temp. Found sensor ohmed within spec. I narrowed down issue to ACU not shutting off and allowing fan to stop, after replacing ACU I connected unit to WiFi. Found upper oven light wouldnt shut off and ui light button would turn back on after 2 seconds on its own after it was turned off but while turned off upper oven lights were still lit. Called whirlpool techline (Sr#7731872615). Also found ui showing f6e4 error after ACU replacement. Found ui would turn lights off/on in diagnostics but not normal operation. Will need office to reschedule once availability of parts is known. ; ordrng 1 W11297709 (Ui control) and 1 W11325541 (2) and 1 W10883049 (Door latch) and 1 W11261167 (Acu)"

We serviced a

MAYTAG DRYER

Model MED6200KW0

Near Austin, TX 78739

Arrived onsite for unit not drying properly when using the sensing dry. Let the customers know about the load sizes can make a difference when the clothes hit the sensor. Went ahead and changed the sensor and Called tech line. Said to test the unit if it passes with the air and heat. Said also about the load sizes and picking the correct temperature settings will make a difference. If there is an air flow issue in the wall as well it can hurt the performance of the unit. spoke with JR got sr#7731869006. Let customer know of the things will need to be done to help possibly fix the issue. No other issues at this time. Job complete.

We serviced a

KENMORE DRYER

Model 417.880427

Near Lago Vista, TX 78645

Arrived on site to install previously diagnosed parts. I installed the new knob shaft. The unit is now working as designed. Call complete.

We serviced a

WHIRLPOOL DRYER

Model WED4950HW0

Near Bastrop, TX 78602

"Arrived onsite for dryer not functioning. Upon arrival tested unit and unit did not start. Inspected unit and found failed thermal fuse. Replaced fuse and tested. During inspection and testing, found supply voltage issues. Found intermittent power issues. Notified customer to seek electrician to correct issue at outlet . Job complete"

We serviced a

WHIRLPOOL REFRIGERATOR

Model GD5NVAXSA01

Near Austin, TX 78730

"Arrived on site to diagnose refrigerator that is not dispensing ice. On arrival customer let me know that the motor isnt making noise, the door just opens and closes. Checked at auger motor and found motor is dead, and the wiring harness and connector has excessive corrosion and is breaking down. Wires are getting stiff, and terminals are corroded. No repair to be made. Harness non repairable without a new door.

We serviced a

KITCHENAID DISHWASHER

Model KDTM404KPS0

Near Lakeway, TX 78738

"Arrived on site to replace dishwasher panel ss, replaced panel, customer inspected and approved, no leaks detected job complete"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF555SDFZ09

Near Austin, TX 78745

Arrived on site and found both sections of refrigerator are room temperature. Inspected compressor and found it will turn on for two seconds and then turn off. Replaced start device and this had no positive effect. A new compressor will be needed to correct issue.; ordrng 1 W10507884 (Compressor) and 1 WPW10313899 (Evap) and 1 Wpsav4 (Stub) and 1 W10143759 (Dye drier)

We serviced a

MAYTAG DRYER

Model MED7230HW1

Near Austin, TX 78759

Arrived on site to follow up on dryer throwing F3E1 error and not starting. Per tech line installed new wiring harness due to failure with sensor wiring. Retested unit and found unit still will not start. Checked start windings on motor and found failed. Replaced motor and tested. Unit still will not start. Checked thermal fuse again and found fuse open. Replaced thermal fuse and unit started. Unit now working as designed. Call complete.

We serviced a

KITCHENAID RANGE

Model KGSS907SSS01

Near Austin, TX 78751

"Arrived on site ,replaced safety gas valve ( igniter not needed ) Checked connections with leak detector . Preheated oven . All checked normal . No gas leaks detected at time of service.

We serviced a

WHIRLPOOL RANGE

Model WGG745S0FS02

Near Pflugerville, TX 78660

Arrived onsite for range turning itself on. Upon arrival found unit bezels and handle on loosely. Adjusted both spoke with customer no bezel not actually contributing to unit being on and made sure handles were snug had customer test. Unit is now operating as designed. Job Completed.

We serviced a

AMANA WASHER

Model NTW4516FW3

Near Austin, TX 78745

"Arrived on site and inspected washer and found no saved error codes. Ran all functions in manual diagnostic cycle and then automatic test cycle and everything is working properly. Raised front feet to center basket and tub. Discussed correct operation with customer, how to avoid unbalanced loads and correct detergent usage. Washer is operating as intended, job complete"

We serviced a

WHIRLPOOL DRYER

Model MEDC465HW0

Near Burnet, TX 78611

Arrived on site to diagnose a dryer that will not turn on. Found timer not registering position and replaced timer. Tested and found all is functioning properly at this time.

We serviced a

WHIRLPOOL DISHWASHER

Model DU810SWPU0

Near Round Rock, TX 78664

Arrived onsite for not draining and found unit may have had a one time clog and determined unit to be in good working order. Advised customer on design of the dishwasher. All checks good.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF555SDFZ05

Near Leander, TX 78641

"Arrived on site for sealed system. We gained access to the compressor and punctured the dryer. I found 50psi in the system. We evacuated the system and replaced the compressor, dry and access valve. We pulled a vacuum on the system for 10 minuets and found it holding as designed. We put a measured charged into the system and found low side at 1 psi and the high side at 145 psi. We temp tested the freezer and found the temperatures dropping. We noticed when the customer turned on his carpet cleaner the fridge lost power for a second and the compressor would not turn back on. I had the customer turn the carpet cleaner off and the compressor kicked back on after a power reset. I recommenedthe customer have an electrician one out and make sure the house boat can handle the amp draw for multiple appliances being on at one time. When the unit is on by itself it is working as designed. Job complete."

We serviced a

ELECTROLUX RANGE

Model EW36IC60LS1

Near Austin, TX 78737

"Arrived onsite for unit not turning on. Got into the unit, And found that the power board was burned up.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHZ05

Near Round Rock, TX 78664

Arrived onsite for refrigerator not cooling. Upon arrival found unit evap completely frosted over ordering unit evap harness control and UI all to be replaced at once spoke with customer on unit needing to be defrosted for work. Cleaned condenser coils and spoke with customer on cleaning front of coils for air flow.; ordrng 1 W11545823 (Evap harness)

We serviced a

WHIRLPOOL WASHER

Model MVW7230HW0

Near Austin, TX 78732

Arrived on call for complaint of not washing properly. Ran test load and rye washer is working properly.

We serviced a

WHIRLPOOL DISHWASHER

Model WDTA50SAKZ0

Near Marble Falls, TX 78654

Arrived on site to diagnose a dishwasher that is leaking. Found heating element not able to mount to tub and replaced element. Tested unit and found all is functioning properly at this time. No leaks were found after service was performed.

We serviced a

GE REFRIGERATOR

Model GSS23WGTABB

Near Buda, TX 78610

"Arrived on site to inspect unit for not dispensing ice when the paddle was pressed, upon inspection found the solenoid rusted shut, replaced solenoid and tested. All functions returned.

We serviced a

WHIRLPOOL RANGE

Model WEG750H0HZ0

Near Blanco, TX 78606

"Arrived on site for customer complaint of unit not heating in oven consistently, found faulty ignitor, I replaced ignitor, unit tested good."

We serviced a

WHIRLPOOL WASHER

Model MVWB855DC2

Near Round Rock, TX 78681

Arrived onsite and found unit operating with F6e2 error and no function.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF989SDAM02

Near Round Rock, TX 78681

Arrived onsite and diagnosed icemaker with E2 error and found unit was unable to be cycled in diagnostics.

We serviced a

UNKNOWN VENTHOOD

Model WVU17UC0JS0

Near Round Rock, TX 78681

"Arrived onsite for vent hood not starting. Upon arrival found unit had good voltage but unit switch wouldnt send voltage to motor, ordering switch. ; ordrng 1 W11369105 (Switch)"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRB322DMBM03

Near Austin, TX 78756

Arrived on site for no ice . Found supply line pinched . Straightened line . All checked normal. No water leaks detected at time of service. Job complete

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT519SZDM06

Near Pflugerville, TX 78660

"Arrived on site for fridge not cooling. I inspected the unit and work area. I gained access to the evaporator and found no frost pattern and no uv dye leaking. I gained access to the compressor and found it turning on and off, not making it pass the start up. I evacuated the system from the low side and found the high side not evacuating. I removed the dryer and used nitrogen on the system I found it clear. I cleared the dryer and reinstalled it. I pressurized the system with 120 psi of nitrogen and found it leaking. I inspected the evaporator and found no leaks. I found no leaks at the exposed lines at the evaporator. I called techline and spoke to rich

We serviced a

HOTPOINT DRYER

Model DLB1550RALWH

Near Georgetown, TX 78626

"Arrived on site to inspect dryer drum not turning. Upon further inspection, the customer advised the unit turns on and heats, but the drum doesnt turn. I raised the top panel, and found the drive belt was broken. I installed a new belt and tested and unit is operating as designed. I cleaned the lint from inside the unit. No lint observed at the end of service, job completed."

We serviced a

WHIRLPOOL ICE MACHINE

Model KUID508HPS00

Near Austin, TX 78746

"Arrived on site for no power to pump,replaced control,harness and pump,ran diagnostics pump powered on. Ran unit though a normal operating cycle,water filled reservoir and pump powered on."

We serviced a

WHIRLPOOL DISHWASHER

Model WDT970SAHZ0

Near Pflugerville, TX 78660

"Arrived onsite and tested unit for not washing well, and found all functions operating as designed. Advised customer on best use and care principles. All else checks good."

We serviced a

WHIRLPOOL WASHER

Model WTW6120HC0

Near Austin, TX 78748

Arrived on call to replace previous diagnosed parts. After installation test operation.

We serviced a

WHIRLPOOL WASHER

Model WTW7120HW0

Near Austin, TX 78748

"Arrived on site and replaced strike diagnosed on previous visit, after replacement ran a diagnostic cycle to confirm operation, job complete."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX986SIHZ01

Near Leander, TX 78641

Arrived onsite to install previously diagnosed parts. I installed the freezer bin and both side brackets. The unit is working as designed at this time. I advised the customer on overloading to help the issue from returning. Job complete.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHZ05

Near Leander, TX 78641

Arrived onsite for refrigerator with ice forming on the door or IM. Upon inspection I found some condensation build up on the ceiling of the FC in front of the ice bin. The droplets are dripping and freezing on the bin. I found a piece of ice stuck in the ice chute door which would cause air infiltration and condensation. I called techline to report. SR#7731863792. They recommended stocking the FC with more items to help with moisture control. I verified no air leaks when the ice door is closed. And no other air leaks anywhere on the unit. I explained to the customer my findings and possible solution. No water leaks detected during time of service. Job complete.

We serviced a

KITCHENAID MICROWAVE

Model KCMS2055SSS2

Near Austin, TX 78738

"Arrived on site to test unit for continuing to run when unit open, tested unit found shorted out switches, replaced switches, tested unit, unit now working as designed,

We serviced a

WHIRLPOOL RANGE

Model KFGG500ESS0

Near Georgetown, TX 78626

"Arrived on site to inspect range oven light not working and customer is unable to remove the glass cover. Upon further inspection, I removed the glass cover and placed a new bulb in the unit that the customer provided and placed the glass cover back on the bulb housing. Light is operating as designed. No gas leaks detected during service, job completed."

We serviced a

MAYTAG WASHER

Model MVWB855DC3

Near Lago Vista, TX 78645

Arrived on site for a washing machine not having power. I tested voltage at the wall and found it good. I replaced the console and control. The unit was now responsive. I ran a diagnostics cycle and the unit ran through as designed. No leaks observed at the time of service. Call complete.

We serviced a

KITCHENAID REFRIGERATOR

Model KRFC300ESS04

Near Austin, TX 78704

"Arrived on site for no ice . Unit is dispensing water . Ran harvest. Unit completed harness but not activating water valve . Jumped valve , threw breaker twice . Replaced IM, now not harvesting. Ordering IM , valve ,both harness hv control. No water leaks detected at time of service. Call to set return ; ordrng 1 W10317076 (Hv control) and 1 W10793298 (Im) and 1 W11224411 (Harnes rear) and 1 W11174745 (Evap harness)"

We serviced a

KITCHENAID RANGE

Model KSDG950ESS2

Near Austin, TX 78704

"Arrived onsite for range damage, verified damage, need cooktop and vent trim to fix issue, office to reschedule; ordrng 1 W11170796 (Trim vent) and 1 W11117943 (Cooktop)"

We serviced a

WHIRLPOOL DISHWASHER

Model JDB8200AWP3

Near Austin, TX 78702

Arrived on site for dishwasher not draining . Found broken glass in drain pump. Removed glass . Ran diagnostics all checked normal. No water leaks detected at time of service. Job complete.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT108FZDB02

Near Del Valle, TX 78617

Arrived onsite for refrigerator not cooling in both sections. Upon inspection found unit is having a sealed system issue. No frost pattern on coils only ice ball on top right corner on cap tube. Fans are operating. Will reach out to office if moving forward. Job complete

We serviced a

MAYTAG WASHER

Model MHW5630HW2

Near Austin, TX 78704

"Arrived on site for thumping noise . Ran diagnostics, no error codes . Customer did mention unit was dropped on stairs during delivery . Removed front panel. No frame damage . Shocks in good condition. Did find drain hose twisted on back of unit , readjusted hose on back . Unit passed diagnostics. No water leaks detected at time of service. Job complete"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX986SIHZ

Near Austin, TX 78734

Arrived on call for complaint of no power. Found power control failed. Replace control and test.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX735SDHZ03

Near Austin, TX 78750

"Arrived on site to diagnose refrigerator not making ice. On arrival customer let me know that it now has a full bucket of ice, but sometimes will go days without making any. Checked unit and found the left RC door is having a hard time contacting the switch, resulting in the unit thinking the door is open. Installed plastic square to resolve switch contact. Advised on cleaning condenser coils and making sure unit can breathe for best results. Unit now working as designed. Call complete."

We serviced a

WHIRLPOOL DISHWASHER

Model KDTM504EPA0

Near Austin, TX 78732

"Arrived on site for to test unit for water on bottom left corner, test unit found tubing elbow not connected the right way, adjusted tubing elbow, tested unit, unit now working as designed, no leaks detected job complete"

We serviced a

KITCHENAID REFRIGERATOR

Model KRFC704FBS00

Near Austin, TX 78736

"Arrived on site for no ice. Ran ice box fan,fan not powering on,removed fan checked voltage reading 5 Vdc diagnosed a defective main control

We serviced a

WHIRLPOOL RANGE

Model WFE525S0JS1

Near Waco, TX 76708

"Arrived on site for arrange that is tripping the breaker. Inspected unit and work area. Confirmed the customer complaint and checked all elements, Control, and terminal block for any signs of burning or grounded wires. Found no wires grounded. Checked continuity between both elements in both elements checked fine. Attempted to preheat and found the oven was shutting off within 30 seconds. Spoke to PR and was advised to check the breaker. Found the breaker on a GFCI breaker for a 240 V circuit. Was advised to remove the wires off the boiling element and check to see if it will drip at that point. Remove the wires and found that the unit did not trip but did notice that when pulling off the wiring one of the wires was loose and not fully gripping the backside of the broil element. Tightened the fitting onto the boil element and then re-tested the unit. The unit did not trip the breaker on two separate preheating occasions. The unit is now working as designed. Call complete."

We serviced a

WHIRLPOOL DISHWASHER

Model WDT750SAHZ0

Near Pflugerville, TX 78660

Arrived onsite and repaired handle and determined electrical short to be present at outlet in specific positions. Advised customer that ongoing trouble with power would require a new outlet to solve.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHZ05

Near Del Valle, TX 78617

Arrived onsite for refrigerator water dispenser not functioning. Found kink in water line. During inspection found. Ice maker fill tube frozen. Potential weeping valve. Ordering valve for return visit.; ordrng 1 W11162042 (housing) and 1 W11284458 (icemaker) and 1 WPW10179146 (valve-inlt)

We serviced a

WHIRLPOOL MICROWAVE

Model JMW2430IM02

Near New Braunfels, TX 78132

Arrived on site to test unit for console not powering on. Verified console receiving proper voltage. Cycled power to unit and console now powered on. Tested microwave for 3mins. and oven to 350. Unit is working as designed. Job complete.

We serviced a

WHIRLPOOL DISHWASHER

Model WDF331PAHS1

Near Andice, TX 78628

"Arrived on site to inspect dishwasher not working. Upon further inspection, I placed the unit in diagnostics showing error code F4E3, failed motor. I cleared the code and continued with testing. Water dispensed into the tub and the motor failed to come on. I advanced through testing and the dispenser, drain pump and element all are functioning as designed. I removed and replaced the sump/motor assembly and retested and unit is operating as designed. No water leaks observed during service, job completed."

We serviced a

MAYTAG WASHER

Model MVWX655DW1

Near Austin, TX 78747

"Arrived on site and inspected washer and found error code for lid lock and motor fault. Ran all functions in manual diagnostics and then again in an automatic test cycle and everything passed. Inspected Gearcase assembly and control board and did not find any issue. Washer is operating properly, job complete"

We serviced a

WHIRLPOOL RANGE

Model WFG550S0HZ2

Near Leander, TX 78641

Arrived onsite to install previously diagnosed parts. I installed the regulator valve but I couldnt get the burner to situate on the valve stem. Its about a half inch or so off. After a few attempts and further inspection I found the frame is bent in the left rear I called techline to document SR#7731872917 . No gas leaks detected during time of service and I verified operation of the cooktop. Job complete.

We serviced a

KITCHENAID COOKTOP

Model KCES550HSS00

Near Austin, TX 78728

Arrived onsite to install previously designed part. Inspected unit and work area and found right front burner inop due to its element being burnt out. Installed new burner and reinstalled unit and tested all burners and now unit is operating as designed. Job complete

We serviced a

KITCHENAID DISHWASHER

Model KUDS30FXSS2

Near Johnson City, TX 78636

"Arrived on site for customer complaint of unit not washing and shutting down after about 90 seconds, found failed wash motor, I replaced wash motor and ran diagnostic test cycle, unit tested good.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX986SIHZ02

Near Dripping Springs, TX 78620

"Arrived on site for customer complaint of water filter cover not staying up in place, found broken latch, I replaced latch, unit tested good."

We serviced a

UNKNOWN VENTHOOD

Model UXT5236BDS1

Near Round Rock, TX 78665

Arrived on site to install previously diagnosed parts. Removed blade and motor and installed new Whirlpool tested motor and new blade. Installed cotter pin onto blade to keep blade secure. While motor was removed I inspected the actual mount that the motor attaches to and it is secure. Vent hood is level. Allowed fan to run on low then high speed for fifteen minutes. No noise detected. Lights working as designed. Customer confirmed that typically after five to ten minutes the noise starts. Job completed.

We serviced a

WHIRLPOOL OVEN

Model WOS51EC0HS02

Near Pflugerville, TX 78660

Arrived onsite and found breaker tripped. Reset and tested. Oven began to heat and tripped breaker again. Found unit is on an arc-fault breaker. Advised customer that breaker is not compatible with oven design and their may be a wiring issue. Advised that breaker must be made compatible prior to any repairs being viable.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF535SWHA05

Near Pflugerville, TX 78660

Arrived onsite and found unit door bin cracked and unable to hold stable. Ordering bin to repair function. ; ordrng 1 WPW10289497 (Bin)

We serviced a

KITCHENAID ICE MACHINE

Model KUIC15PHZS0

Near Lakeway, TX 78734

Arrived on call for complaint of no power. Found the external pump failed. Will need 2 hours to complete please send RJ.

We serviced a

KITCHENAID REFRIGERATOR

Model KBSD608ESS01

Near Leander, TX 78641

Arrived onsite for refrigerator not cooling in RC. Upon inspection I found the RC at 65 and FC at -10 I found frost forming on the ceiling above the ice bin and some on the evaporator cover. I called techline to document. I found the ice chute has a gap in the liner where it looks like a piece was not snapped in at the factory or the insulation had created a cavity techline advised attempting to seal this gap. I sealed with permagum and exposed the evaporator. I found the right side has a block of ice blocking then returns most likely due to the air leak in the ice chute. I installed a new evap motor due to it already being approved and customer stating it was the part that they had been waiting for. I steamed out all the ice from that side and cleared the return vent. I advised the customer that if the issue persists than the next step would most likely be a new door. SR#7731867545. No active leaks detected. Job complete.

We serviced a

WHIRLPOOL OVEN

Model WOD93EC0AS01

Near Austin, TX 78738

"Arrived on site to test unit for no power and door locked, tested unit found open fuse, replaced fuse,tested unit by heating both ovens to 350 degrees, top and bottom blowers working as designed, job complete"

We serviced a

WHIRLPOOL DISHWASHER

Model WDF331PAHS1

Near Georgetown, TX 78626

Arrived on site for FASTNER FOR TOE PLATE IS DEFECTIVE-DISHWASHER ISN'T FLUSH IN THE SPACE IT'S IN. Found dishwasher legs adjusted down too far making the bottom of the dishwasher stick out further than the top. Adjusted legs up to allow dishwasher to sit more even. Explained to customer how a raised pitch is important to prevent the top rack from sliding out when door is opened. After adjusting legs we tested the top rack and it didnt slide forward. Ran diagnostics to ensure dishwasher is running as designed. No error codes came on. Dishwasher completed all cycles and heated. Installed new retainers on kick plate. No leaks detected. Job completed.

We serviced a

WHIRLPOOL RANGE

Model WFE525S0HS1

Near Austin, TX 78744

Arrived onsite for unit still Tripping the breaker. Currently said that it would trip the breaker when either he was using the oven or using the cook top. Called tech line. Let them know of all things customers complaint was about and let them know all that was replaced. said to remove the metal strap that goes between the neutral and ground wire as it could cause the tripping the breaker issues. Said to test the unit and if the unit shuts off to check the breaker and feel if it?s getting hot under a load and if it is the issue then the breaker could be breaking down and customer needs an electrician to fix the power on the house side. Got Sr#7731866976. Took off the metal strap from the terminal block. Tested the unit up to 350. Unit got up to temperature with no problem and stayed on. Went outside to check the breaker and felt that it was getting a bit warm. Let customer know that there may be an issue with the breaker and an electrician will need to be called out to fix the breaker or the plug. No issues at this time. Job complete

We serviced a

KITCHENAID REFRIGERATOR

Model KRFF507HPS02

Near Leander, TX 78641

Arrived onsite for refrigerator with dented right side RC door. Upon arrival I confirmed the complaint and replaced the door. The customer brought to my attention that the left side handle is loose. I found the screw that secures the handle to the door has stripped out the outer shell so the door will need to be replaced. Advised customer on timeframe. Office to R/S due to part availability. ; ordrng 1 W11518741 (Left side door) and 1 W11449276 (Screw)

We serviced a

MAYTAG WASHER

Model MVW7232HW0

Near Killeen, TX 76543

"Arrived on site and inspected washer lid lock issues. Confirmed the complaint and found both the latch and strike were both defective causing the malfunction. Removed and replaced both and during the next diagnostics cycle the unit failed to start and kept flashing back to the previous screen when I attempted diagnostics cycle. The unit also never engaged full to preform a spin cycle. The wash plate was the only thing spinning, not the basket. Unit flashed F6 E3 communication error ACU cannot hear MCU. It also had Basket re-engagement failure F7E4 error Im ordering the ACU , MCU and also the clutch assembly. Office to schedule return services due to part availability ; ordrng 1 W10754448 (CLUTCH) and 1 W11130429 (Fascia assembly with UI harness) and 1 W11419171 (CONTROL) and 1 W10905022 (Clutch assembly) and 1 W10905025 (Slider)"

We serviced a

WHIRLPOOL REFRIGERATOR

Model KRFC300ESS00

Near Meadowlakes, TX 78654

Arrived on site to diagnose a refrigerator that is over cooling in the rc. Found items in unit blocking airflow and trapping freezer air. Advised homeowner on findings and no further repairs needed. No leaks were found at time of service.

We serviced a

WHIRLPOOL RANGE

Model WFE366LVS

Near Killeen, TX 76549

Arrived on site and inspected oven temperature issues. Set the unit to 350 and waited approximately 12-15 minutes and unit reached set temp. I did have to add 10 degrees to the calibration to get the set temp. Uni tested properly. Job complete

We serviced a

WHIRLPOOL ICE MACHINE

Model KUIO338HSS00

Near Kingsland, TX 78639

Arrived on site to replace door panel for ice machine. Replaced outer panel and dealer is going to install pump they sent the builder. Job is complete.

We serviced a

WHIRLPOOL DISHWASHER

Model WDT750SAHZ0

Near Whitney, TX 76692

Arrived on site for a dishwasher that?s still having issues washing dishes. Inspected unit and work area. The customer advised that the unit will run one to several cycles every time they reset it but they end up with an error code of an F4 E3 (wash motor not running). Ran the unit through diagnostics and did not find any sort of error codes. Attempted to run a normal wash cycle and found the unit filling and washing. Checked resistance through the wash motor and found it within range. I called whirlpool Techline and spoke to Steve SR# 7731872899.He advised me to run a diagnostic auto test to see if the unit errored out any codes due to a potential possibility of the unit having a separate issue. He also asked me to wiggle the wires as the unit was washing in the cycle. I did both and the unit did not error out or have any issues within the diagnostic test. The phone was disconnected so I called back and spoke to Travis SR# 7731872899. He advised that the issue could be a communication issue but advised to replace the wash pump motor and control at the same time.

We serviced a

MAYTAG WASHER

Model MVWB835DW4

Near Kyle, TX 78640

"Arrived on site to inspect unit for a broken lid, upon inspection found the left hinge snapped causing issues. Ordering lid. Office to reschedule ; ordrng 1 W11259006 (Lid)"

We serviced a

MAYTAG WASHER

Model MHW7100DC0

Near New Braunfels, TX 78130

Arrived on site to test unit for leak. Found bellow needs replaced. Needing clamp and bellow to fix issue. ; ordrng 1 W11266654 (Clamp) and 1 W11106747 (Bellow)

We serviced a

WHIRLPOOL COOKTOP

Model WCE55US6HB00

Near New Braunfels, TX 78132

"Arrived on site to inspect unit for a broken glass piece on cooktop, upon inspection found the glass cracked on the bottom right corner,Checked cooktop and found it was broken as well. Ordering new cooktop. Office to reschedule ; ordrng 1 W11225081 (COOKTOP)"

We serviced a

WHIRLPOOL MICROWAVE

Model WMH53521HZ4

Near New Braunfels, TX 78130

"Arrived on site to inspect unit for burning out bulbs, upon inspection found the control board shorted causing repeat issues, replaced control and tested. Complete"

We serviced a

WHIRLPOOL WASHER

Model MHW6000XG2

Near New Braunfels, TX 78130

"Arrived on site to test unit for water valve staying open. Found constant voltage to valves. Was able to reset unit. Cold valve not opening properly and water level switch was not reading properly. Recommended replacing control, valve and water level switch. Needing control and water level switch.Office to reschedule. ; ordrng 1 WPW10304342 (Water level switch) and 1 W10427972 (Control)"

We serviced a

JENN-AIR REFRIGERATOR

Model JFFCC72EFS02

Near Blanco, TX 78606

"Arrived on site for customer complaint of unit not making ice and leaking, found ice maker not reaching home position, ordering ice maker. ; ordrng 1 W11557002 (Ice maker) and 1 Cnote (Office to reschedule)"

We serviced a

KITCHENAID OVEN

Model KOSE500ESS00

Near Horseshoe Bay, TX 78657

Arrived on site to diagnose an oven that is not turning on after self clean. Found thermal fuse and tod both open. Both parts will need to be replaced to complete repairs and return date set; ordrng 1 WPW10545255 (Fuse) and 1 WP4449751 (Tod)

We serviced a

WHIRLPOOL OVEN

Model WOS51EC0AS02

Near Austin, TX 78717

Arrived on site for a wall oven with no power. I turned the unit off at the breaker and then tested the fuse. I found the open and needing to be replaced.

We serviced a

WHIRLPOOL DISHWASHER

Model WDF520PADM7

Near Leander, TX 78641

Arrived onsite for dishwasher tripping breaker. Upon inspection I found no error codes stored on the unit. I took off the toe kick and found what looked like water stains on the insulation. I noticed the dispenser was not fully sealed and there is a gap on the right corner closest to the door handle. I took off the outer panel and found evidence of a leak at the dispenser and one of the screws that secure the dispenser is missing. I let diagnostics run through and it went through all functions except the dispenser. ; ordrng 1 WPW10671905 (Dispenser) and 1 WPW10177098 (Screw)

We serviced a

WHIRLPOOL DRYER

Model WED4950HW0

Near Manor, TX 78653

Arrived onsite for dryer making noise. Upon arrival tested unit. Found that dryer vent was not seated correctly to hose. Adjusted dryer position. Tested unit and unit noise went away. Unit is functioning properly. Job complete

We serviced a

WHIRLPOOL DISHWASHER

Model WDT750SAHZ0

Near Hutto, TX 78634

Arrived on site for Not Starting or Operating - Dishwasher. Found kick plate missing from bottom of dishwasher. Placed in diagnostics and F6E4 came on. No other error codes came on. Cleared error code and found small piece of plastic stuck underneath float. Removed and tested in diagnostics. Found water was turned off. Turned on water and diagnostics cycle ran through all cycles and heating element heated as designed. No leaks detected.

Sours: https://applianceexpresstx.com/service-history-12/

Mode wrf736sdam13 diagnostic

Customer complaint: Refrigerator won’t get colder than 45 degrees.
Error Codes:


Whirlpool Refrigerator Repair Canton

Repair notes: ** On schedule: Oct 16, 2020 09:30AM
Upon disassembly of the refrigerator evaporator cover, we found that the damper was stuck shut and not opening or closing. We entered the manual diagnostic mode of the computer on the refrigerator and were unable to get it to cycle property. After installing a new damper assembly which included the thermistor, it is operating correctly. In manual mode, that opens and closes and registers the same. Issues resolved amd the refrigerator is cooling property.

Open full TECH SHEET and wiring diagram.

To Enter Service Diagnostics Mode:
NOTE: Refrigerator must not be in lockout mode prior to entering Service Diagnostic Mode.
1. Press SW1 and SW2 simultaneously for 3 seconds.
2. Release both buttons when you hear the CHIME indicator. The display will show “01” to indicate the control is in Step 1 of the diagnostics routine.
To Exit Service Diagnostics Mode, Choose one of the Following Options:
■ Press SW1 and SW2 simultaneously for 3 seconds
OR
■ Unplug refrigerator or disconnect power
OR
■ Allow 20 minutes to pass.
Following the exit of the diagnostic mode, the controls will then resume normal operation.
NOTES:
■ Cooling diagnostics are Service tests 1 through 7 and 32 through 39.
■ Dispensing diagnostics are Service tests 8 through 31.
■ Each step must be manually advanced.
■ Press SW5 to move to the next step in the sequence.
■ Press SW4 to back up in the sequence to the previous step.
■ Diagnostics will begin at Service Test 1.
■ Each step is displayed in the 2 digits of the dispenser user interface
display.
■ The step results are displayed in the 2 digits on the dispenser user interface
and display 2 seconds after the step number is displayed.
An amber “Order Filter” light will be shown to designate that the step number is being displayed, and a red “Replace Filter” light will be shown to designate that the status of the step is being displayed.
■ All button and pad inputs shall be ignored and all inputs shall be off except as described in the actions for each step.
Service Test – 1: FC Thermistor
■ The board will check the resistance value of the thermistor and display flashes results on the Temp display (01 = pass, 02 = open, 03 = short).
Service Test – 2: RC Thermistor
■ The board will check the resistance value of the thermistor and display the results on the Temp display (01 = pass, 02 = open, 03 = short).
Service Test – 3: Evaporator Fan and Air Baffle Motors
■ Turn on the FC evaporator fan and the air baffle motor.
■ Monitor the air baffle feedback. SW3 (01 = fan on. Air baffle open, 02 = fan
on. Air baffle closed).


Parts (if required):
WPW10479155-CONTROL


Job: Refrigerator repaired in Canton, Ohio #SJO7234.


CHECK US OUT! Sam’s many positive GOOGLE REVIEWS assures NEW customers that Sam’s Appliance Repair is a wise choice to fix any home appliance.

HIGHLY CONVENIENT repair REQUEST SYSTEM lets you book your appliance repair at your convenience. Customers love it.

ONLY 2 MINUTES TO BOOK YOUR REPAIR online.

Don’t delay. You can get your appliance repaired today.

Like this:

LikeLoading...

Related

Categories RepairTags Refrigerator WhirlpoolSours: https://www.cantonappliancerepair.com/whirlpool-refrigerator-repair-wrf736sdam13-located-in-canton/
Whirlpool kitchenaid refrigerator troubleshooting #KSF26C6XYY #6WSC20C6YY

I had to hold her back. - Did you think they were toys. No, everything is for real. Now there are two red stripes on your ass. And at the end there will be five.

Now discussing:

Anxious at heart. Trifles, it will pass. Let's go get dressed. Throwing off their robes, the girls went to the wardrobe. Jasmine untied the knot she had brought with her from home and pulled out old, well-worn shorts made from used jeans.



880 881 882 883 884